Quantum Data 780C User Manual Download Page 123 | Manualshive

Page: 123 / 240

background image

780C Multi-Interface Interoperability Tester

– User Guide

Page 122

September 29, 2014

Revision A1

Table 6-2: Audio Analyzer

Audio IEC Header decoded data (left side)

Description

Word length

Audio word length. One of:



16 bit



20 bit



24 bit

6.4.5

Procedures for Audible Monitoring of LPCM Audio from an Digital Video Source Device

You can monitor the incoming stereo LPCM audio on the HDMI, HDBaseT or SDI IN port at the headphone
jack on the front edge of the 780C. You can also monitor a single channel of LPCM audio through the
embedded speaker. You can select what channels of a multi-channel LPCM to monitor on the stereo
headphone jack or which single channel on the speaker using the screens provided. Use the following
procedures to configure the audio monitoring of the incoming LPCM audio through the headphone jack and
embedded speaker.

1. Connect the HDMI system devices to the 780C as shown in the diagrams below. The HDMI source device

output is connected the 780C

HDMI, HDBaseT or SDI IN

connector is the audio is routed through an

HDBaseT distribution device. Refer to the diagrams below:

2. Touch select

Audio Monitor Settings

from the

Home

menu shown below.

«
...
121
122
123
124
125
...
»

Summary of Contents for 780C

















































































































































































































































Reviews:

No comments

Related manuals for 780C

Brand: Samson Pages: 4

Brand: C-LOGIC Pages: 2

Brand: Omega Engineering Pages: 22

Network Card-MS

Brand: Eaton Pages: 26

Brand: Omega Pages: 31

Brand: Panasonic Pages: 1

Brand: KALEAS Pages: 64

Brand: UEi Pages: 5

Brand: RHS Pages: 8

Brand: Lutron Electronics Pages: 20

Brand: Rion Pages: 4

PASPORT PS-2174

Brand: PASCO Pages: 4

Brand: Unipro Pages: 2

Brand: MRC Pages: 14

Brand: Tonghui Pages: 65

Brand: Hammond Pages: 36

Brand: SIMET Pages: 2

Brand: Xylem Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands