background image

7

 

Adjustments 

 

The parameters can be changed on the 
control unit by means of the display and the 
joystick. 
The movements of the joystick have the following 
effects: 
• Vertical joystick movement (upward/downward) ->

 

Scroll through the displayed information. 

• Horizontal joystick movement (to the left/to the right) ->

 

Change the settings. 

• Shortly press in the joystick in the rest position 

-> 

Validation OK.

 

 

7.1

 

Motion parameters (PARAMETER) 

 

Parameter  Description 

Setting range 

Default 

Vo 

Opening speed (velocity open) 

0..14 (5…50°/s) 

Vc 

Closing speed (velocity close) 

0..14 (5…50°/s) 

TOEx 

Hold-open time opening element inside/outside (time hold 
opening element inside/outside) 

0...60 s 

3 s 

TKey 

Hold-open time Key (time hold opening element Key) 

0...180 s 

5 s 

TDelay 

Starting delay (time delay lock) 

0,0...4,0 s 

0,2 s 

FDelay 

Relieving force during unlocking (force delay), only effective 
if TDelay is > 0 

0,0...7,0 A 

OFF 

TLock 

Door rectification time (time press close) 

0,0...4,0 s 

0,5 s 

FLock 

Pressing force during locking (force lock), only effective if 
TLock is > 0 

0,0...7,0 A 

2,0 A 

FSlam 

Accelerating function (force slam) 

0...10 

OFF 

FWind 

Obstacle detection optimized for exterior doors (force 
wind) 

OFF 
OPEN 
CLOSE 
BOTH 

OFF 

Fo 

Opening force (force open) 

0...9 

Fc 

Closing force (force close) 

0...9 

Foh 

Hold-open force (force open hold) 

0...9 

Fch 

Interlocking force (force close hold)   automatically 
programs FLock and FDelay if these are 0 

0,0...3,5 A 

Ao 

Opening angle of the door (angle open) 
If the opening angle is changed during the operating mode 
OPEN, the operating mode MANUAL needs to be 
selected for closing the door. 

20...(190°) Rod dep. 

95° 

Rod 

Type of rods (Rod)                        
 
 
 

 
STD-PH 
SLI-PL 
SLI-PH 

STD-PH 
 

dAxis 

Distance between rotation axis of the door hinges and the 
mounting level of the drive unit (distance Axis). dAxis is an 
approximate value. Depending on the installation situation, 
dAxis may have to be adapted. 

-8...+25 cm 
Rod depending 

0/+8 cm 
Rod dep. 

 

 

Normal rods pushing function 
Sliding rods pulling function 
Sliding rods pushing function 

Summary of Contents for FD 10




























Reviews: