quadient DS-200iQ Manual Download Page 76

Page: 76 / 231

Select the required Seal mode from the list (default set to

Always

Other options include the following:

Off

- Envelope is left unsealed with flap closed.

No-seal label select

- Reads no-seal character in label.

Off, flap open

- Envelope is left unsealed with flap open (not available if an

Output Sorter is fitted).

No envelopes

- Envelope feeding is disabled to allow forms only.

Press

once the desired settings have been made.

Advanced Envelope Mailset Settings

Press

Edit Advanced

to set the order of documents inserted into the envelope as

shown below.

Select the required order that documents are inserted into the envelope from the

list (default set to

Automatic

If the order is set to

Manual

, documents are inserted in the order

created in the job.
Document Order is not available when reading.

| Page 74 | May-29-2020 11:33 |

Operator

IMOS

Settings

Summary of Contents for DS-200iQ








































































































































































































































Search results

Summary of Contents for DS-200iQ

Reviews:

quadient DS-200iQ, Manual, Page: 76 / 231

Search results

Summary of Contents for DS-200iQ

Reviews: