manualshive.com logo in svg

quadient DS-200iQ, Manual, Page: 217 / 231

Share
Download
quadient DS-200iQ Manual Download Page 217

Versatile Feeder Specifications

8.3

Hopper Capacity

Up to 1000 of 80gsm (20lbs bond)

A4 Documents unfolded:

Up to 500 of 80gsm (20lbs bond)

A4 Documents (Z-Fold):

Up to 250 (2.4mm)

Booklets:

Up to 500

C5/C6 Envelopes:

NOTE

:

Quantities shown above are maximum figures. Depending upon other conditions,
actual quantities may be lower than those shown.

Enclosure Details

Enclosure Size

Min. 148mm (5¾”)
Max. 305mm (12”)

Width:

NOTE

:

Min. pack width for individual items is 210mm (8¼”).

Min. 76mm (3”) for non-reading units
Min. 93mm (3

⅝

”) for reading units

Max. 216mm (8½”)

Length:

NOTE

:

Max. suggested width difference between inserts is 32mm (1¼”). This may be
increased subject to testing. If this difference is exceeded, the insertion fingers will
not cover the edges of the narrow insert and may cause insertion problems.
Sandwiching a narrow insert between two wider ones may resolve this problem.

215

| Page 215 | | May-29-2020 11:33 |

8

Technical

Specifications

Summary of Contents for DS-200iQ








































































































































































































































Reviews:

No comments