quadient DS-200iQ Manual Download Page 102

Page: 102 / 231

•

Dumb

- Franks every mail-piece that passes. No feedback between the Inserter

and Franking machine. Neither will stop if an error occurs.

•

Franking machine

- Franks mail-pieces determined by the Franking machine

software. Allows feedback between the Inserter and Franking machine. Either

machine will stop if an error occurs on either machine.

•

Pass-through

- Allows every mail-piece to pass un-franked.

Select the required

Franker control

setting from the list of options and then press

as shown below.

Finally select the

Franking job

from the list (e.g. Current job).

Output Conveyor Settings

The following Output Conveyor settings are available:

100

| Page 100 | May-29-2020 11:33 |

Operator

IMOS

Settings

Summary of Contents for DS-200iQ








































































































































































































































Search results

Summary of Contents for DS-200iQ

Reviews:

quadient DS-200iQ, Manual, Page: 102 / 231

Search results

Summary of Contents for DS-200iQ

Reviews: