QTech 1U Hardware Installation Manual Download

Page: 27 / 221

Hardware installation manual

Qtech Platform 2U Server Product Technical Manual

www.qtech.ru

the management software

developed by Intel for its

Chipset. When updating the

BIOS with ME FW online, the

jumper must be installed and

removed after the update is

complete. In other cases, the

jumper is not required.

JBAT1(CMOS CLEAR)

Clear the CMOS Connector, the
jumper is not connected by
default, and the jumper is valid
when plugged in

JP3(ME RECOVERY)

Plug in the jump to force the ME

to be restored to the default

settings

J39(SATA DOMPOWER)

SATA PWR 3pin Connector,

external power supply for SATA

DOM

J13

CPLD programming interface

Hard disk backplane assembly



1U4 3.5” backplane as shown

TOP surface:

Summary of Contents for 1U






























































































































































































































Search results

Summary of Contents for 1U

Reviews:

Related manuals for 1U

Brands by name

Popular brands

QTech 1U, Hardware Installation Manual

Search results

Summary of Contents for 1U

Reviews:

Related manuals for 1U

Brands by name

Popular brands