background image

32

 

©  Copyright 2020 QSAN Technology, Inc. All Rights Reserved. 

 

 

 

3.5.

 

Replace Malfunctioning PSU

 

XCubeNXT comes with two redundant Power Supply Units (PSU) that can be hot swapped when the 
PSU is not functioning. If a PSU or its fan failed to function, please see the instructions below to 
replace the malfunctioning PSU:

 

 

 

 

CAUTION:

 

The power supply unit is a heavy and fragile; please use both hands while 
installing, removing, or carrying them. Recommended place for removing the 
power supply unit: the system is in a well-secured rack or on a stable surface.

 

 

1.

 

Unplug the power cord from the PSU to be replaced.

 

2.

 

Remove the PSU from XCubeNXT.

 

Push the lever of the PSU at the rear panel in the indicated direction. Pull out 
the PSU from the XCubeNXT.

 

 

3.

 

Prepare a new PSU, and push it back to the slot until you hear a click. Please make sure that the 
direction of the PSU is correctly installed, to prevent any potential damage caused by improper 
installation.

 

 

3.6.

 

Replace System Controller

 

If the system failed to function, please contact QSAN support for further examination. If you need to 
replace the system controller, please see the instructions below:

 

 

 

 

CAUTION:

 

1. The controller module is heavy and fragile, please use both hands

 

while installing, removing, or carrying the controller module.

 

Summary of Contents for XCubeNXT XN8000D






































































Reviews: