background image

 

  

 

  

 

 

 Qonnex 

38 

Quick start 2-Wire v3.0 

REL.44, Modbus I/0 module 

The REL.44 module has 2 bi-stable, potential-free 

10A relay contacts and 2 low-power solid-state 

outputs for switching coupled consumers. 
In addition, there is also a P1 connection for 

reading the digital meter* and 2 pulse inputs for 

counting and / or time measuring consumers via 
impulses.  

 
This module can be wired

 

 via Modbus with a 

MEMo3 and from there configured and controlled. Multiple REL.44 can be 

connected to the MEMo3 web server.  
 

The REL.44 is a 'Modbus slave' i/o module and can therefore also be used to 
connect with any Modbus master, as Modbus relay, but also as P1 to Modbus 

and or pulse to Modbus interface. The list of Modbus registers can be found 

on the 2-wire website. 
 

The push button on the front serves to (temporarily) pair the REL.44 with 

WiFi to download the latest firmware. 
 

*REL.44 is compatible with all Belgian and Dutch digital meters.  
Via P1, REL.44 reads: 

 

Consumption import high rate 

 

Consumption import low rate 

 

Consumption export high rate 

 

Consumption export low rate 

 

Rate (high or low rate) 

 

Consumption of gas (if measuring device is present) 

 

Consumption of water (if measuring device is present) 

 

Consumption import high + low rate 

 

Consumption export high + low rate 

 

Consumption import – export (positive or negative) 

1. Connect: 

Power supply: [1] 

Always first connect the optional 9–15  ±10% Volt 

DC power supply and only then  

[2]

  P1 port input with galvanic 

isolation with RJ12 cable (max 3 meters). 

Only

  with a Belgian or a 

DSMR 5.x digital meter one does NOT 

need to connect an external 15 VDC 
power supply* 

*Provided that the digital meter provides sufficient 

power: the COM LED must first be constantly lit to 

flicker on/off after approx. 10sec. If there is not 

enough power from the digital meter, the REMI will 

restart itself after about 3 minutes of charging, or 

disconnect itself and only connect when all LEDs are 

off. 

Modbus

:

[3]

  shielded EIB bus cable 4x 

0.5mm² use and respect the color code 

GAB=black, yellow and white. ReMI or 

set as Modbus master with 2-WIRE 
meters, or Modbus slave in a MEMo3 

setup, not both simultaneously.

 

Pulse IN

 [4]

  2x NO potential-free reed 

contact, 0-5v/2mA, cable max. 2 meters, section 2x0.5mm². Pulse 

duration min. 100msec, max. 10 pulses/hour.  

Pulse-OUT: [5] 

 2x low power solid state contact with optical 

isolation, max. 24 VDC/5mA,  cable  max. 2m, section 2x0.5mm². 

Generates via logic either consumption pulses of P1 meter, or a low-
power switching contact. 

Relay output:

 

 [6] 2x 

 bi-stable potential-free 10A/230V relay 

contact up to max. 2300 Watt ohmic load, or use as release contact 

to the control of eg heat pump, charging station, boiler, 

accumulation,... Connection wire min. 0.25mm² ... Max. 2.5mm². 

Please note:

 

•Mono-phase module

: connect both contacts to the same phase!  

•Bi-stable

: in case of voltage interruption, they retain their position! 

LED

:[7]

PWR

:power status,  

COM

:Communication, 

R1

 and 

R2

: status 

relays. 

Antenna

:  On the SMA connector the WiFi antenna screws, when 

mounted in metal cabinet order the optional antenna with magnetic 

base. 

2. Configuration in MEMo3b via tablet of PC: 

See also MEMo3b manual 1.3. 

In summary

1.

 

Login as installer under Level3: 
password 'Level3' and then 'CANCEL' 

2.

 

Create a channel with 'ADD 

CHANNELx' 

 

3.

 

When the channel appears click on the CHx

 

 button so that the channel 

configuration opens see figure 

4.

 

As a module type you choose 'REL 44' 

5.

 

Enter Modbus address and that MUST be the same for all channels of 
this REL.44 module 

6.

 

Enter the serial number e.g.

 

 '44R00770' 

7.

 

As a fashion you choose either: 

a.

 

'P1 port' and complete

 

 P1 Type and Protocol (Belgium=6) 

b.

 

'Bi-stable', choose Relay 1-4, at para3 power in Watts 

c.

 

'Counter', choose IN1 or 2, give at para 3 pulse weight 

d.

 

'Time', choose IN1 or 2, at para3 consumption after 1 hour  

8.

 

Press 'SEND' 

9.

 

Press 'SAVE' 

Below is an example with 3 channels of the same REL.44 module. 

 

3. Pairing with WiFi for upgrade 

REL.44 is controlled via Modbus from the Memo3 module. The 

connection with WiFi is only necessary if you want to upgrade. 

 
Once REL.44 is connected correctly (see power supply REL.44) the 

green PWR LED will be constantly lit followed by the orange COM 

LED which after about 10 sec. flickers on/off every second. To 
REL.44, the 'WiFi access point' mode can be applied for about 5 

seconds to press the JOIN/UPG button until the orange LED is 
constantly lit. REL.44 now becomes "WiFi access point". 

 

NOTE: WiFi range

: Make 

sure that during WIFI connection and also 

during firmware upgrade the distance between REL.44,router, 
smartphone or PC is as short as possible!!! 
NOTE: Change existing WiFi link:  Orestartand then press the JOIN/UPGR 
button after

 

2-3 seconds (approx. 5 sec) until the COM LED remains 

solidly lit. REL.44

 

 now becomes 

 

"access point". 

 

Reviews: