QNAP QTS 4.5 Series User Manual Download Page 18

Page: 18 / 575

Situation

User Action

Steps

An administrator is locked out
and no other administrators
can access the account.

An administrator must restore
the factory settings.

Press the RESET button on the back of the
NAS for three seconds.
The NAS restores the default administrator
password and network settings.

Note

For information on the default
admin password, see

Backup/

Restore

Warning

Pressing the RESET button for 10
seconds resets all settings and
deletes all data on the NAS.

QTS Navigation

Task Bar

No.

Element

Possible User Actions

Show Desktop

Click the button to minimize or restore all open windows.

Main Menu

Click the button to open the

Main Menu

panel on the left side of the

desktop.

Search

• Type key words to locate settings, applications, and help content.

• Click an entry in the search results to open the application, system

utility, or

Help Center

window.

If the application is not yet installed, QTS opens the corresponding
download screen in the

App Center

window.

Tip

App or utility search results are classified into

Systems

Application

, and

Help

Volume Control

Important

This feature is
only available
on models with
certain
hardware
specifications.

Click the button to view the following:

• Media Volume: Click and drag the slider thumb to adjust the audio

volume for applications that use the built-in speaker or line-out jack.

• HD Station

• Music Station

• OceanKTV

• Audio Alert Volume: Click and drag the slider thumb to adjust the

volume of system audio alerts.

QTS 4.5.x User Guide

Overview

Summary of Contents for QTS 4.5 Series
































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for QTS 4.5 Series

Reviews:

Related manuals for QTS 4.5 Series

Brands by name

Popular brands

QNAP QTS 4.5 Series, User Manual

Search results

Summary of Contents for QTS 4.5 Series

Reviews:

Related manuals for QTS 4.5 Series

Brands by name

Popular brands