manualshive.com logo in svg

QMS Magicolor WX, User Manual

Share
Download
QMS Magicolor WX User Manual Download Page 42

Configuring the 

Windows 95 

Printer Driver

QMS magicolor WX User’’'s Guide

2-2

Configuring the Windows 95 

Printer Driver

»

Note: 

This section explains how to configure the QMS magicolor WX 

printer driver in Windows 95. The following section explains how to 
configure the QMS magicolor WX printer driver in Windows NT 4.0.

Setting the Printer Driver Defaults

1

From the Windows 95 Start menu choose Settings. Then 
choose Printers.

2

In the Printers window, select either the QMS 

magicolor

 WX 

Color or the QMS 

magicolor

 WX Monochrome printer driver.

n

QMS 

magicolor

 WX Color provides 300x300 and 600x600 

dpi resolution for color printing and 600x300 dpi resolution for 
monochrome printing. It also allows you to set color printing 
options. (See “Resolution” on page 2-9 and “Configuring 
Color Options” on page 2-11.)

n

QMS 

magicolor

 WX Monochrome provides 300x300 and 

600x600 dpi resolution for monochrome printing. It doesn’t 
allow you to set color printing options. (See “Resolution” on 
page 2-9.)

3

From the File menu choose Properties.

The following tabs appear: 

n

General—Allows you to name the printer, use a separator 
page, and print a test page. See your Windows documenta-
tion.

n

Details—Allows you to set interface connection details. See 
your Windows documentation.

n

Sharing (optional)—Allows you to set up the printer so others 
on the network can use it. See your Windows documentation.

Summary of Contents for Magicolor WX

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands