manualshive.com logo in svg

QMS Magicolor WX, User Manual

Share
Download
QMS Magicolor WX User Manual Download Page 225

QMS World-

wide Offices

A-5

QMS Customer Support

QMS World-wide Offices

QMS United States and Latin America

General Contact
1 (334) 633-4300
Fax 1 (334) 633-4866
Email [email protected]
Internet http://www.qms.com

Customer Response Center (CRC)
Technical Assistance

1 (334) 633-4500 

 7:00 am–6:00 pm Central Time M–F

Fax 1 (334) 633-3716
Internet http://www.qms.com

Bulletin Board Service

1 (334) 633-3632 

Latin America Fax
1 (334) 639-3347

National Service
Service Information, Installation, and Maintenance Pricing

1 (800) 762-8894 

On-Site Service and Depot Repair Information

1 (800) 858-1597

7:00 am–7:00 pm Central Time

Spare Parts Ordering and Information

1 (334) 633-4300 x2530

8:00 am–5:00 pm Central Time

QMS Canada

General Contact
1 (514) 333-5940 or 1 (800) 361-3392
Fax 1 (514) 333-5949

National Service
On-Site Service and Depot Repair Information

1 (800) 268-4969 

8:30 am–7:00 pm Eastern Time

Spare Parts Ordering and Information

1 (905) 206-9234 x238

8:30 am–5:00 pm Eastern Time

Bulletin Board Service
1 (905) 206-0084

QMS in Japan

(81)- 3 3779-9600
Fax (81)-3 3779-9650 

Summary of Contents for Magicolor WX

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands