Home
/
QMS
/
Magicolor WX
/
User Manual

QMS Magicolor WX, User Manual

Share

Page: 131 / 248

QMS Magicolor WX User Manual Download Page 131

Replacing

Consumables

5-5

Maintenance

Replacing Consumables

»

Note:

Dispose of toner and developer cartridges in a safe manner,

meeting all local and federal regulations. Also, you should handle only
one color of toner and developer at a time to avoid contaminating
other colors. Use a toner vacuum to clean up powder spills in the
printer, if necessary. If toner gets on your hands or clothing, lightly
dust off as much as possible and rinse any toner remaining on hands
or washable clothing with cool water to remove the rest.

M

WARNING!

The toner is a highly combustible powder; never burn it.

Also, avoid inhaling loose toner or getting it around your eyes; it can
cause respiratory problems and eye irritation.

ACHTUNG!

Bei dem Toner handelt es sich um ein gefährliches und

leicht entzündliches Pulver; es darf deshalb niemals mit offenem
Feuer in Berührung kommen. Einatmen oder Berührung mit Haut und
Augen ist ebenfalls zu vermeiden, da dies zu Beeinträchtigungen der
Atemwege, Haut- oder Augenreizungen führen könnte.

Replacing a Toner Cartridge

1

Remove the top cover.

«
...
129
130
131
132
133
...
»

Summary of Contents for Magicolor WX

























































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands