![Qimarox PRORUNNER mk1 Assembly Instructions Manual Download Page 10](http://html1.mh-extra.com/html/qimarox/prorunner-mk1/prorunner-mk1_assembly-instructions-manual_3166154010.webp)
Assembly instructions PRORUNNER mk1
10
2.4 Safety devices
It is not permitted to disassemble, bypass or disable any safety devices.
See the user manual for the required references.
The PRORUNNER mk1 may not be started or must be immediately taken out of service
if one of the safety devices is defective.
The PRORUNNER mk1 must have the following safety devices:
Emergency
stop
Use the emergency stop (A) in the event of an an emergency.
Fencing
Qimarox B.V is obliged to guard the PRORUNNER mk1 with a fence. The access
door(s) must be secured with (interlock) door switches. These switches must be
included in the emergency stop circuit.
The doors must not never be closed if someone is inside the fencing.
The machine must be switched off and secured when prolonged work is carried out
inside the fencing.
Always put all of the safety devices that were removed back in place as soon as
maintenance work has been completed.
2.5 Safety instructions
Observe the following general safety instructions:
Connect the PRORUNNER mk1 in accordance with the basic health and safety requirements
of the relevant European directives.
Before you put the PRORUNNER mk1 into service, check that the machine has been installed
in accordance with the instructions in this manual.
Never switch on the power to the PRORUNNER mk1 or start the PRORUNNER mk1 if there
are people in contact with the machine or if there are people inside the danger zones.
Switch off the power to the machine using the main switch before carrying out any
maintenance or repair work on the PRORUNNER mk1. Secure the main switch with a
padlock.
Keep your hands away from danger zones.
Be careful of loose clothing and hair.
Wear head protection.
Make sure there are no people or objects within reach of the moving parts of the
PRORUNNER mk1.
Replace damaged or defective parts before putting the PRORUNNER mk1 into service again.
Maintenance on the PRORUNNER mk1 must be carried out by trained engineers.
Always be on the alert for dangerous situations.
Summary of Contents for PRORUNNER mk1
