background image

Safety

 

  

 

 

18 

UM Pallet dispenser PD2 v2.0 EN 

 

3.4.6  Check valves 

To prevent the carriers and lifting forks to lower by gravity when the air is released from the 
machine, the cylinders have been fitted with check valves. This also prevents the stack from 
falling. 

 

WARNING 

Danger potential energy and moving parts. Check valves keep air trapped inside 
the cylinder. This can cause a cylinder to move when for instance an air tube or 
blockage is removed. Before maintenance or repair, it is necessary to vent all 
cylinders. See section 6.2 for special safety regulations. 

 

For safety reasons the check valve for closing the lifting arm is short-circuited in the following 
positions: 

 

Carrier middle position for a de-stacker 

 

Carrier bottom position for a stacker 
 

 

WARNING 

Danger of stack or pallets falling. When de-stacking, NEVER keep the pallet 
stack suspended in the middle position. In an emergency stop the lifting arms 
are depressurised in the middle position and the stack will drop. 

 

3.5  Electrical safety 

3.6  Sound level 

The A-weighted emission sound pressure level L

pA 

at workstations does not exceed 70dB(A). 

 

Note 
The sound pressure level applies to typical pallets made of wood or plastic. 
Pallets made of other materials might increase the sound level. 

 

3.7  Personal safety 

For your own safety use personal protective equipment. 

Always wear proper personal protective equipment when working with, on or near the 
machine. 

The following table gives an overview of the required personal protective equipment 

Summary of Contents for PD2















































Reviews: