background image

 

Safety 

 
 

 

 

UM Pallet dispenser PD2 v2.0 EN 

11 

 

3  Safety 

3.1  Intended use of the machine 

The machine is exclusively intended for the stacking of empty pallets described in this 
manual. Refer to chapter 4 for a detailed description of the specifications of use.  

The machine is always set up within a larger transport system in which empty pallets 
are loaded on and off the machine. 

 

WARNING 

Any other use of the machine is strictly forbidden. 

 

 

WARNING 

It is 

strictly forbidden

 to lift persons with the machine or to stand on 

the pallets or lifting frame. 

 

 

WARNING 

It is 

strictly forbidden

 to overload the machine with too much weight or 

with too many pallets. See specification sheet or type plate and sticker 
“Max load” on the machine. 

 

 

WARNING 

It is 

strictly forbidden

 to use the machine with pallets out of spec or of 

insufficient quality. See specification sheet. 

 

3.2  User types and qualifications 

The following user types are referred to in this manual: 

 

The operator 

 

The mechanical installer 

 

The electrical installer 

 

The maintenance engineer 

Only qualified personnel may operate the machine. A qualified 

operator

 has 

experience with operating machinery and is informed about the contents of this 
manual. An operator must be familiar with the contents of Chapters 1, 2, 3 and 4 and 
with the Operating Manual. 

An 

electrical installer

 is only qualified if a person has attended appropriate training 

and/or attained appropriate industry standard recognized qualifications. Qimarox can 
provide training if required. 

The 

maintenance engineer

 must be familiar with the full content of this manual and 

with the Operating Manual. All maintenance work should be performed by qualified 
maintenance personnel 

Summary of Contents for PD2















































Reviews: