Qiagen PyroMark Q24 MDx User Manual Download

Page: 75 / 104

Troubleshooting

PyroMark Q24 MDx User Manual 01/2016

7-7

Comments and suggestions

e) White remains

(Sepharose beads)
in the

immobilization plate

If more than 1 min has elapsed since the plate (or

strips) was agitated, agitate again for 1 min
before capturing the beads.

7.5

Verification of correct installation and
operation

PyroMark Control Oligo is sold together with the PyroMark

Q24 MDx and required to verify proper installation and
operation of the system. The PyroMark Control Oligo consists
of one wobbled base (measured as %C), single bases of all

four nucleotides, and homopolymers of two and three bases.
For information on how to use the PyroMark Control Oligo,

see the

PyroMark Q24 Validation Oligo Handbook

, supplied

with the product.

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands