Qiagen PyroMark Q24 MDx Page 10 User Manual Download | Manualshive

Page: 10 / 104

background image

Safety Information

1-4

PyroMark Q24 MDx User Manual 01/2016

1.4

Chemicals

WARNING

Hazardous chemicals

The Denaturation Solution used with the vacuum

workstation contains sodium hydroxide, which is irritating
to eyes and skin.

Always wear safety glasses, gloves, and a lab coat.
The responsible body  (e.g., laboratory manager) must take
the necessary precautions  to ensure that the surrounding

workplace is safe and that the operators are not exposed
to hazardous levels of toxic substances (chemical or
biological) as defined in the applicable Material Safety

Data Sheets (MSDSs) or OSHA,* ACGIH,

†

or COSHH

‡

documents.

For more information,  visit
www.qiagen.com/support/msds.aspx.
Venting for fumes and disposal  of wastes must be in

accordance with all national, state, and local health and
safety regulations and laws.

* OSHA: Occupational Safety and Health Administration (United States of America).

†

ACGIH: American Conference of Government Industrial Hygienists (United States of America).

‡

COSHH: Control of Substances Hazardous to Health (United Kingdom).

1.5

Mechanical hazards

The lid of the PyroMark Q24 MDx Instrument must remain
closed during operation of the instrument. An audible

warning signal will alert you if the lid is opened when it is not
safe.

WARNING

Moving parts

To avoid contact with moving parts during operation of the
PyroMark Q24 MDx Instrument, the instrument must be
operated with the lid closed.

Do not remove the cover panels since there are no user-
serviceable parts inside. If there is a problem with the
PyroMark Q24 MDx Instrument, contact QIAGEN

Technical Services immediately.

«
...
8
9
10
11
12
...
»

Summary of Contents for PyroMark Q24 MDx









































































































Reviews:

No comments

Related manuals for PyroMark Q24 MDx

Brand: Waterwise Pages: 12

Brand: ParaBody Pages: 38

Brand: Obdstar Pages: 10

Brand: FJC Pages: 2

Brand: Vahle Pages: 96

Brand: Garelick Pages: 2

Brand: Gardico Pages: 2

Brand: OceanSat Pages: 85

Brand: Xiitech Pages: 6

Brand: Valmar Pages: 78

Brand: Valhalla Scientific Pages: 64

Saturn 2000 GC/MS

Brand: Varian Pages: 9

Brand: Coba Pages: 2

Brand: Anslut Pages: 20

Brand: H&S Pages: 35

Brand: Insportline Pages: 8

Brand: Major tech Pages: 36

Brand: Waeco Pages: 254

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands