EN-6
EN-5
EN-
Remote Control
USE
CLOCK
to
setup
the
time
of
the
unit
1
.
connect
the
ac
on
(
.
2
.
short according to the time button
,
the
time
will
flashing
on
the
lcd
display
.
3
.
Rotate
BACK
、
NEXT
to
select
the
number
of
the
time
.
you
can
setup
the
time
format
by
12h
or
24h
.
4
.
press
time
button
to
confirm
.
5
.
then
you
can
set
the
hour
and
the
minute
with
the
same
method
of
steps
3
-
4
.
6
.
with
the
same
method
of
steps
3
-
4
.
Rotate
The following operation must be in standby mode)
after setup the unit time, long press the time button can setup the unit begin working time ,
Note: after setup the beginning time, the lcd will display the radio/cd/usb/sd/aux/blue mode,
the BACK or NEXT to choose the mode, then it press time button to affirm, otherwise
it playusb or aux mode first.
Radio
reception
1
.
FUNCTION
select
RADIO
.
.
Press BAND to select the desired wave band: FM STEREO, AM, FM, FM ST.
3.Tune to required station by
Manual Tuning
: Rotate BACK or
NEXT and then release within 1 sec.
Auto Tuning
:
Preset Channel:(
FM
30 Preset memories,
)
(1)
BACK
/
Select desired station.
(2) Press PROGRAM button once , The MEMORY number indicator begins steady
in the display.
(3) Press PRESET-UP OR PRESET- DN buttons to select the desired number.
(4) Press PROGRAM button to save that station.
(5) Repeat steps (1) to (4) procedures for other stations.
4.After end of program. press PRE-UP or PRE-DN to start play the frequency that you
selected or Press number key on the remote control.
5.
6.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting.
7.Turn off the radio by press FUNCTION button select other mode or press power button
to off the unit.
Press
button
mode
Press the play/pause button enter the automatic channel
mode, and to be put automatically sets.
[VOL-]or [VOL +] to adjust the volume.
2
Rotate BACK
/
NEXT or press PRE
-
DN
/
PRE
-
UP.
scan
AM 10 preset memories
Rotate
NEXT
Rotate
8.Switch
on
again
after
shut
down
,
the
memory
frequency
still
exists
.
MONO/STEREO
-Press MO/ST button once, to mono state
.
-Press MO/ST button twice, to stereo state, stereo is displayed
.
*
Please pull out the plastic paper from the battery door before use the remote control.
*
When the remote control operation becomes unstable or the distance from which the
remote control works is shorter. replace the batteries with new ones
.
*
Using the remote control unit
To use the remote unit, point at the REMOTE SENSOR and press the buttons gently and
firmly. Remote control operation is possible within approximate 18ft (6m). However, since
the remote control range is less when the unit is used at an angle, use directly in front of
the REMOTE SENSOR, for maximum distance
.
Do not expose the REMOTE SENSOR to strong light (direct sunlight or artificial lighting)
and make sure that there are no obstacles between the REMOTE SENSOR and the
remote control unit
.
1. POWER BUTTON
2. OPEN/CLOSE BUTTON
3
.
INTRO
BUTTON
4
.
MUTE
BUTTON
5
.
RANDOM
BUTTON
6
.
P
-
UP
BUTTON
7
.
REPEAT/MO/ST
BUTTON
8
.
PROGRAM
BUTTON
9
.
BACK
BUTTON
10
.
FUNCTION
BUTTON
11
.
NEXT
BUTTON
12
.
EQ
BUTTON
13
.
PLAY
/
PAUSE
BUTTON
14
.
P
-
DOWN
BUTTON
15
.
BBS
BUTTON
16
.
STOP/BAND
BUTTON
17
.
NUMBER
KEY
18
.
VOL
-
BUTTON
19
.
VOL
+
BUTTON
4
5
1
9
10
14
15
18
19
6
2
11
8
7
13
12
17
16
3
RANDOM BUTTON
-In the player CD/MP3/USB/AUX , press the RANDOM button can be played at random.
Press again to cancel
.
BBS BUTTON
-In the player CD/MP3/USB/BT/AUX/RADIO, press the BASS button can make into the
bass state. Press again to cancel
.
EQ BUTTON
-In the player CD/MP3/USB/BT/AUX/RADIO, press the EQ button to change music style.
-When playing the music, press this button
is in the classica-rock-popular-jazz-FLR.
MUTE BUTTON
-In the player CD/MP3/USB/BT/AUX/ RADIO, press the MUTE button to enter the mute state.
Press again to restore volume
.
INTRO BUTTON
-In the player CD/MP3/USB,
press the INTRO button into 10 seconds browsing repertoire
state, press
again
cancel browse.
