q-Tech OLT-QSW-9010 Cli Configuration Manual Download Page 44

Page: 44 / 101

User Manual

4. Unicast service configuration

www.qtech.ru

Service binding port:

OLT (config-gpon-onu1 / 1: 1) # remote service 1 gem 1 eth_1 / 1

Note:
QTECH

OLT

supports

remote

service

configurations.

The

Remote

service configuration

strictly

filtered

and

requires

all

the

same

service

when

configuring

it,

that

is, which

means

VLAN

and

VLAN+COS

service

can't

mixed.

4.5.2.

Remote UNI Configuration

OLT support 5 modes: access / hybrid / transparent / trunk / xlate.

Access mode:

OLT (config-gpon-onu1 / 1: 1) #remote uni eth_1 / 1 vlan-mode
access pvlan 100

Hybrid mode:

OLT (config-gpon-onu1 / 1: 1) # remote uni eth_1 / 1 vlan-mode
hybrid pvlan 100 tag 200

Transparent mode:

OLT (config-gpon-onu1 / 1: 1) # remote uni eth_1 / 1 vlan-mode
transparent

Trunk mode:

OLT (config-gpon-onu1 / 1: 1) # remote uni eth_1 / 1 vlan-mode
trunk tag 100 200

Xlate mode:

OLT (config-gpon-onu1 / 1: 1) #remote uni eth_1 / 1 vlan-mode xlate
100-200

Summary of Contents for OLT-QSW-9010






































































































Search results

Summary of Contents for OLT-QSW-9010

Reviews:

Related manuals for OLT-QSW-9010

Brands by name

Popular brands

q-Tech OLT-QSW-9010, Cli Configuration Manual

Search results

Summary of Contents for OLT-QSW-9010

Reviews:

Related manuals for OLT-QSW-9010

Brands by name

Popular brands