background image

3

CLEANING

OPERATING INSTRUCTION

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to 
qualified service personnel if service is needed.
1. Before cleaning and assembling, do not plug the pins into the socket.
2. To ensure adequate air circulation to the motor. Keep vents at the rear of the 
    motor housing from dust, fluff and etc. A vacuum cleaner can not be used to 
    clean these vents before unplug. Do not disassemble the fan remove fluff.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent. 
4. Do not use any abrasive detergent or solvents to avoid scratching the sufrace. 
    Do not use of the following as a cleaner: gasoline, thinner, bending.
5. Do not allow water or any other liquid into the motor housing or interior parts.

MAINTENANCE INSTRUCTION

Speed control
Speed is controlled by the button switch. (-0 -1 -2 -3)
  0-Off  1-Low   2-Medium   3-High
Oscillation control
To make the fan oscillate, push down on the oscillation knob located on the top 
of the motor housing. To stop the fan down from oscillating in the position 
desired, push on the oscillating knob once more.
Tilt control
The airflow can be adjusted upward or downward by tilting the fan head to a 
vertical angle as desired.

9

1

2

3

4 5

6

7

10

8

12

11

OPERATING INSTRUCTIONS
Model: KF00405

3 Speed

Oscillating

Desk Fan

Read these instructions and keep for future reference

FITTED WITH
BS1363
BSI APPROVED PLUG

1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap. 
    Thoroughly remove soap film with dry cloth.

DISPOSAL

Do not dispose of electrical appliances as unsorted 

municipal waste, use separate collection facilities. Contact your 
local government for information regarding the collection systems 
available. If electrical appliances are disposed of in landfills or 
dumps, hazardous substances can leak into the groundwater and get into the food 
chain, damaging your health and well-being.

2

1. Detach screw from base of the fan.
2. Match locking tab to base and click into position.
3. Tighten the screw in the base to secure the fan to the base.

ASSEMBLY OF BASE

1. Never insert fingers, pencils, or any other object through the grille when fan is 
    running.
2. Disconnect fan when moving from one location to another.
3. Disconnect fan when removing grilles for cleaning.
4. Be sure fan is on a stable surface when operating to avoid overturning.
5. DO NOT use fan in window, rain may create electrical hazard.
6. Indoor use only.

PART FIGURE

RULES FOR SAFE OPERATION

1. Front fuard      2. Blade     3. Plastic nut
4. Rear guard     5. Motor shaft      
6. Oscillation knob    7. Fan body     8. Spinner
9. Chassis   10. Speed control buttons 
11. Tight      12. Loose  

1.Remove the spinner on the head unit by turning it clockwise. Then remove the 
   plastic nut by turning it counterclockwise.
2.Place the rear guard to the head unit so that thehandle is upward.
3.Screw on the plastic nut (clockwise) securingthe fan guard on the head unit.
   (Step 1.2.3  see Fig.1).
4.Discard the small plastic sleeve located on the motor shaft.
5.Install the fan blade onto the motor shaft. Makesure the fan blade slot fits into 
   the retaining pin ofthe motor shaft.(Step 4.5 see Fig.2)
6.Attach the spinner to the motor shaft by turningit counterclockwise to secure the 
   fan blade.
7.Place the circlip around the rear guard(You canskip this step if the circlip is 
   already attached to the rear guard.)
8.Secure both guards firmly by tightening the fan guard then close easy cllip.
   (Step 7.8 see Fig.3 )

ASSEMBLY OF BLADE OF GRILLES

Read Rules for Safe Operation and Instructions Carefully. 

1. Do not leave the fan running unattended.
2. Keep electrical appliances out of reach from Children or infirm persons. Do not 
    let them use the appliances without supervision.
3. Ensure that the fan is switched off from the supply mains before removing the 
    guard.
4. If the supply cord is damaged, it must be replaced by manufacturer or its service 
    agent or a similarly qualified person in order to avoid a hazard.
5. This appliance is not intended for use by persons (including children) with 
    reduced physical, sensory or mental capabilities, or lack of experience and 
    knowledge, unless they have been given supervision or instruction concerning 
    use of the appliance by a person responsible for their safety.
6. Children should be supervised to ensure that they do not play with the appliance.

1

CAUTION

WARNING

WARNING INSTRUCTIONS

PLUG REPLACEMENT 

This appliance is supplied with a BS1363 3 pin plug fitted with a 3 Amp fuse. Should 
the fuse require replacement, it must be replaced with a fuse rated at 3 Amp and 
approved to BS1362.
In the event the mains plug has to be removed/
replaced for any reason, please note:
IMORTANT: The wires in the mains lead are 
coloured in accordance with the following code:
Blue – Neutral
Brown – Live

As the colours of the wires in the mains lead of this appliance may not correspond 
with the coloured markings identifying the terminals in your plug, proceed as follows.
The blue wire must be connected to the terminal marked with an N or coloured black.
The brown wire must be connected to the terminal marked with an L or coloured red.

WARNING:

 Never connect live or neutral wires to the earth terminal of the plug.

NOTE:

 If a moulded plug is fitted and has to be removed take great care in disposing 

of the plug and severed cable, it must be destroyed to prevent engaging into a socket.

Fig.2

Fig.1

Fig.3

Reviews: