3.3 – Internal memory
The memory contains sessions and data saved by the device; it also contains system configuration folders and the coordinates of the finish lines of the
tracks. The memory card contains the following folders:
Folder: SYSTEM File: CONFIG.CFG (file for all product configurations)
Folder: TRACKS File: *.TRK (file for the finish line and split time coordinates)
Folder: SESSIONS File: *.SES (saved sessions file)
Folder: MANUALS File: *.pdf (instructions manuals in several languages)
Folder: IMAGE File: *.bmp (startup image, monochrome bitmap 240x128px)
Please note: All the names and contents of the folders and files have been appropriately formatted; DO NOT change them
manually; only use Race Pro software to read/write the file.
3.4 – RPM cable installation
Important information regarding installation - READ CAREFULLY
- On two-stroke vehicles with strong electromagnetic emissions, such as scooters, go-karts and pocket-bikes, it is necessary to use resistive spark plugs
and shielded caps with 5K resistance. If you don't use shielded caps and resistive spark plugs, the device could measure the wrong values. Spark plugs
manufacturers often mark resistive spark plugs with the letter "R" in their code. For example, NGK BR7ES is a resistive spark plug, while B7ES is its
non-resistive equivalent.
Separate coil (high voltage spark plug wire):
Insert the black wire into the plastic cylinder, bend the end part of the wire to form a "U" and reinsert the
wire into the cylinder; fasten this to the spark plug wire using the double clip (see reference image on the
side). Place the clip at the same distance from the spark plug wire and coil.
Integrated coil ("cigar-shaped" coil on the spark plug):
Turn the coil power plugs 6-8 times and fasten with a cable tie.
In both cases, make sure other coils do not interfere with the plug, as this would detect erroneous rev values.
Make sure the plug is not close to other plugs and try to fasten it to the frame for all its length. Should the rev
values be incorrect, check the device settings.
To fix the RPM cable to the dashboard, unscrew the cross screw that fixes the RPM cable holder (see photo Chap. 2) in the rear side
of the dash ; insert the cable into the plastic part making a "U" as in the photo on the side, close the RPM cable holder by passing the
cable through the appropriate slot and fasten everything with the cross screw.
4 – Usage
4.1 – Switch on/off
To switch on the device, keep the ON/OFF button pressed until the logo appears on the display. To switch off, keep the ON/OFF button pressed until the
device switches off.
In case the dashboard is powered externally via an SS12V100 cable, the ON / OFF button will be disabled and the dashboard will automatically switch on
and off with the external power supply, therefore it is necessary to connect to a power supply under key.
Start Plus also has an automatic shut down feature which switches the device off after 20 minutes of inactivity.
4.2 – Registering sessions
Start Plus will begin to register a new session every time the three following conditions are met:
- the GPS signal has picked up the satellite signal
- the chronometer has been activated (we remind you that the chronometer starts when the internal accelerometer retrieves the departure of the vehicle)
4.3 – GPS signal
GPS signal acquisition can take from a matter of seconds to a couple of minutes. If the device has been switched off for days or the circuit has changed,
the time required for the first satellite retrieval can take 4/5 minutes; when used regularly, detection takes very little time. Acquisition of the GPS signal
is indicated on the display by the GPS icon:
GPS receiver has detected the satellites
GPS receiver has not yet detected the satellites
It is also possible to check the signal received by the satellites by accessing the menu, selecting the INFO icon and subsequently the SAT icon; the ID
numbers of the satellites will appear together with the dB power signal received; if the signal bar is full the satellite is being used, if not, it isn't.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: +39 0721 820434 – Email: [email protected]
