+44(0)333 444 1280 (UK)
[email protected] (UK)
www.pyronix.com
Pyronix Limited, Pyronix House, Braithwell Way, Hellaby, Rotherham, S66 8QY, UK
Tri-detection method
2 digital dual-element passive IR & 1 microwave
doppler unit
Transmission frequency
FM transceiver narrow band
Transmission method and range
Fully encrypted rolling code, 300m
Pet immunity
Up to 24kg, 1m high
Detection speed
0.25 - 2.5m/s
Casing
3mm polycarbonate, 0.4mm HDPE in Lens Area. IP
Rating: IP55
Lenses
UV compensated
Mounting height & range
1m - 1.5m = 12m range
Tamper switches
Both front and rear, and external tamper switch
Temperature
Storage: -40°C to 80°C
Operating: -30°C to 70°C
Dimensions & weight
188 x 77 x 84mm, 0.3kg
Batteries
2x 3V 4700mAh lithium battery packs (BATT-ES1)
Lifetime up to 3 years
Battery information
The batteries supplied with this product have been chosen to provide long service life whilst, for safety reasons, having limited
output current. The battery leads must be connected for operation. When disposing of the product, remove the batteries and
dispose of separately in accordance with the local regulations.
Product information
Applies to electrical products sold within the European community. At the end of the electrical product’s life, do not dispose of it
with household waste. Where possible, recycle the product. Check with your Local Authority or retailer for recycling advice in
your country.
This product operates in a European non-harmonised frequency band. Hereby Pyronix declares that this detector is in
compliance with the essential requirements and other relevant provisions of the Directives. The declaration of conformity may be
consulted at www.pyronix.com/product-compliance.php
Warranty
This product is sold subject to our standard warranty conditions and is warranted against defects in workmanship for a period of
two years (excluding lens and batteries). In the interest of continuing care and design, Pyronix Ltd reserves the right to amend
specifications without giving prior notice.
Environmental Class (EC) IV
9.9GHz:
AT, BE, CH, CY, CZ, DK, EE, FI,
FR, GR, HR, HU, IE, IS, IT, LT, MT, NL,
PL, PT, SI, TR, UAE
10.525GHz:
BE, BR, CH, CY, DK, ES, HU,
IE, IS, IT, MT, MY, NL, NO, SE, SI, UAE,
USA
10.587GHz:
GB, MY
EN
Partcode: XDL12TT-WB / XDL12TT-WD / XDL12TT-WE
Wireless Flat Lens External Detector
RINS1901-1
1. Installation
Scan the QR code for fixing instructions and adapter information. Ensure that the detector is installed
away from reflected sunlight and large objects.
2. Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
3. Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle of detection.
4. LEDs
Four LEDs show the status of the detector.
5. Lens inserts
Use lens inserts to control the coverage area.
6. Learning procedure
To connect the detector to a control panel, follow the learning procedure. When you first install the
batteries in the detector, LED1 and LED4 flash alternately. On the control panel, go to ‘Wireless Device
Control’, then press and hold the LEARN button on the detector until the LEDs start to flash. When
LED1 flashes and the control panel shows it is connected to the detector, the procedure is complete.
After powering up and after learning, there is a 10 minute timer that allows a walk test of the PIR and
microwave sensors. You can set up the sensitivity and microwave range without using the control
panel to perform a walk test. After 10 minutes, the detector enters sleep mode.
7. Signal strength test
On the control panel, check the signal strength of wireless devices. Within 300 seconds, the control
panel shows a signal strength from 0 (no signal) to 3 (strong signal). Hold the detector where you want
to install it and check LED1 and LED4. If LED4 flashes (signal strength 0 or 1), choose a new position
for the detector.
8. Battery level test
On the control panel, check the battery level of wireless devices. Within 300 seconds, the control panel
shows the battery levels. If the battery level of the detector is low, replace both batteries at the same
time.
9. External tamper input
Specifications
4m 8m 12m
1-1.5m
1-1.5m
< 24kg
1m
4m 8m 12m
1-1.5m
< 10m
4m 8m 12m
1-1.5m
> 10m
4m 8m 12m
ON
LED 1
LED 2
LED 3
LED 4
Top PIR activated
Bottom PIR activated
Microwave activated
Alarm
Powering up
Low battery
12m
1.3m
1.3m
~8m
0m
12m
12m
12m
1-1.5m
1
2
3
2
4
5
1-1.5m
4m 8m 12m
1
2
3
4
ON position
LEDs on
Buzzer on
Top PIR high sensitivity
Bottom PIR high sensitivity
OFF position
LEDs off
Buzzer off
Top PIR low sensitivity
Bottom PIR low sensitivity
2
2
Frequency Band (MHz)
Wireless Frequency indicator
433.050 - 434.790
W
B
866.000 - 866.600
W
D
868.000 - 868.600
W
E
