Step 4
Warranty and compliance
Technical Specification
Printed Circuit Board
Battery
DELTABELL-WE
Self Powered External Sounder
Installation guide
Installation Steps: Step 1
Step 2
Step 3
EN50131-4:2009
EN50131-5-3:2005+A1:2008
Security Grade 2
Environmental Class IV
Slide the
PCB
module
upwards.
The sprung
back-tamper
arm can be
retracted to
allow removal.
This must be
done in order to
install the revolving
guides - see step 3.
Place the base on a
flat surface and
ensure it is vertical
using the spirit level
that is already installed. Drill and plug in each of the
fixing locations. The revolving guides will correct any
misalignment. If the Deltabell WE must be mounted
on an uneven surface, it is recommended that a
tamper levelling screw is used to ensure correct
back-tamper operation. See step 2.
Step 5
Fit the lid by sliding its
hinges into place. The lid
can be supported in the
fully open position. To
close the lid, apply a
little force to push the lid
past the holds.
Close the cover, ensure
the tamper is operating
correctly, insert the
25mm long screw
supplied and rotate the
screw cover to a close.
*Lid sold separately
Mounting the
Deltabell WE on an
uneven surface
may cause false
triggering, through
incorrect operation of
the back-tamper.
A POZI number 2 screw
driver is recommended for
adjusting back tamper screw.
NOTE: This is for wall mounting only.
Low voltage Threshold:
Batt1: 2.2V +/-5% at 25 C,
Batt2: 2.5V +/-5% at 25 C
Batteries:
2x 3V 5AHr
Lithium battery packs (BATT-ES1)
Acoustic output:
Tone.
Strobe duration:
10ms
Strobe Frequency:
1Hz
Sound pressure level:
101dBA
Max sound duration:
15 mins
Dimensions:
290 x 285 x 50 mm
Selectable comfort LEDs:
4 second flash rate
Operation from external PSU (optional):
11V to 14V
IMPORTANT NOTE
: The batteries should
still be connected if using an external PSU.
Case Tamper. Reverse polarity protected
The batteries supplied have been
chosen to provide long service life
whilst, for safety reasons, having
limited output current. Replace
only with approved batteries.
To prevent possible damage to
components, any static charge on
your body needs to be eliminated
before touching the inside of the
unit. This can be accomplished by
touching some grounded/earthed
metallic conductor such as a
radiator/pipework immediately
before replacing batteries.
Insert the guides as shown. Make sure that the guides ‘B’
are aligned with the tabs to the right (this is so the PCB
module slides in). Turn each guide until they line up with the
drilled holes, while referencing the spirit level for the correct
alignment, and fix the base firmly to the wall.
Please note, if the Deltabell
WE is installed on an uneven
surface, it is recommended
that you do not tighten up
the wall screws until after
the module is installed
(step 4)
The batteries and battery holder
should be inserted as shown:
Learning the
DELTABELL-WE
onto the Control Panel
When you are ready to learn the device to the
control panel receiving equipment, and when
the equipment is in the learn mode (see the
Control Panel Programming Manual) follow the
procedure below.
1. Make sure the battery is installed correctly
2. Press and hold the Learn button until the
3 LEDs start cycling through the different
colours, then release.
3. The device is correctly learnt when the
green LED flashes.
WARRANTY:
This product is sold subject to our standard
warranty against defects in workmanship for a period of two
years (batteries excluded). Please note: In positions where
the Deltabell WE casing is subjected to high levels of U.V.
sunlight, there may be risk of case colour fading, this is not
covered by the warranty. In the interest of continuing
improvement of quality, customer care and design, Pyronix
Ltd reserve the right to amend specifications without giving
prior notice.
Pyronix Ltd, Braithwell Way, Hellaby,
Rotherham, South Yorkshire, S66 8QY
Customer support: +44(0)845 6434 999
(local rate) or +44(0)1709 535225
Hours: Mon to Fri, 8.00am till 6:30pm
Email: [email protected]
Website: www.pyronix.com
The three coloured LEDs give a
visual indication of the signal
strength.
Green indicates good signal strength
and is a good location to install.
Red indicates poor signal
strength and the device should not
be installed in that position.
If no LED illuminates then the device
is completely out of range.
The blue LED will illuminate when the
device is activated.
RED
BLUE GREEN
RED
BLUE GREEN
RED
BLUE GREEN
RED
BLUE GREEN
RED
BLUE GREEN
Tamper
levelling
screw
BATT1
BATT2
SOUNDER
TAMPER
COMFORT
LEDS
LED OFF
LED ON
LEARN
LED
3
LED
2
LED
1
Comfort LED
Enable/Disable
link
Learn button
Optional
auxillary 12
volt PSU input
PLEASE
NOTE:
The auxillary
12V PSU input
is not polarity
conscious
Battery
Connectors
Sounder
Tamper
Red LED
Blue LED
Green LED
Strobe
Comfort LEDs
RINS1433-3
Tamper switch
For electrical products sold within
the European Community. At the
end of the electrical products life, it
should not be disposed of with
household waste. Please recycle
where facilities exist. Check with
your Local Authority or retailer for
recycling advice in your country.
When disposing of
the product, the
battery must be
removed and
disposed of
separately in
accordance with the
local regulations
Please see the Enforcer 32-WE user,
programming and quick set up manuals for
further information
Place the PCB module, ensuring that the arrow is aligned with the marker (on the left of
the module). Expose the terminals by releasing the latch on the top of the PCB module.
NOTE: The bottom battery holder should be
installed as shown -in order to allow to
installation or removal of the Deltabell
Module.
NOTE: Older Deltabell products were supplied with a single cylindrical
battery type (
1x
BATT-CR34615D) instead of the two square batteries
(
2x
BATT-ES1) in the current product. The different battery types are
NOT INTERCHANGEABLE between products.
Replace like with like under all circumstances.
