Pyle Pro PDCD6000MP Instruction Manual Download Page 6

Page: 6 / 18

- 5 -

16. ON/OFF BUT TON (PITCH)

Press the button to be PITCH ON mode, press it
again on the PITCH ON mode, and blinks with unit
on the PITCH OFF mode.

17. 3 HOT -CUE

This unit will allow you to play from 3 cue points
instantly.
a. Set CUE memory: Press the MEMO button first,

and then press the CUE button to complete the CUE
setting, then this C UE button will light up.
b. Play” CUE” memory: Upon pressing specific CUE
button, it will flash about 5 seconds.

Note: This function is not available during perform
REV ERSE sound effect.

18. SAM. BUTTON

Sampler is a kind of sound effect that you record the music
from the track. While playing the music, you can use the
sampler to mix with music. The maximum length is 32

seconds.

a. Set start point: Press the MEMO key, and then press SAM

button, after memorizing the SA M button flashes quickly (2
times in 1 sec)

b. Set End point: Press the SAM button again, when the end

point is memorized, the S AM button lights up (not flash).

c. Play Sampler: During PLAY mode, press the SA M button,

then the button will flash slowly. (1 time in 1 sec)

NOTE: Refer to parameter setting instruction for sampler

adjustment

19. JOG WHEEL

*Speed Control (SEARCH indicator off)

Rotating the wheel, in play mode, will change the playback
speed accordingly. While rotating clockwise, the player

speed increase; rotating counterclockwise, the speed
decrease.

*Search (SEARCH indicator lights)

Rotating the wheel, the player will forward or backward
quickly. The searching speed changed according to the
dialing speed. It can be carried out by one frame increment.

20. Seamless Loop (2 set)

There is A, B/LOOP/ EXIT, RELOOP buttons.

1 . A BUTTON---“start point” (A point. Also, Cue 1 could be A

point) After setting up the A point, the red Led light up

2 . B/LOOP/ EXIT BUTTON: ---“ End point”(B point). Press the B

/LOOP button to set up the B point and start the loop playback

automatically. Loop lights on the display and the 3 LEDs flash.

Press this button again to exit the LOOP playback.

3 . Return to the loop playback by pressing the RELOOP while in

performance. However, if your want to return to loop playback,

you can press RELOOP BUTTON

4 . Change “ START POINT” and” END POINT” by pressing the

A& B/ LOOP/ EXIT button again

5 . The interval between A and B point must be more than 20

frames; otherwise, the B point will be canceled, then LOOP

function disappear and LOOP fades on the display

21. SOUND EFFECT/ DIRECT ACCESS

BUTTONS

* SOU ND EFFECT OFF

The buttons are direct access keys (0~9). To select the
number of the track you would like to play.

* SOU ND EFFECT ON

The buttons is for sound effect control and it lights up when
the sound effect be chosen and off when the button is

pressed again.

NOTE:

How to set up the parameter; please refer to

parameter setting instruction. (Page

)

SCRATCH:

Move the JOG Wheel backward or forward like

scratching a turntable record. This sound effect can be performed
independently, or in parallel with other effect.

BRAKE:

To change the speed of PAUSE and START. This sound

effect can be performed independently, or in parallel with other
effect.

REVERSE:

The music is playing backward. This sound effect can

be performed independently, or in parallel with other effect.

PHASER:

It sounds like the airplane takes off

FLANGER:

It sounds like another kind of airplane takes off. .

FILTER:

There are bass & treble. To increase the parameter value,

it will cut bass off but keep treble. To decrease the parameter value,

it will cut treble off but keep bass.

CHOP:

The music is chopped with break.

PAN:

Alternatly playing right and left signal

ECHO:

Have the effect as ECHO.

22. SOUND EFFECT ON/OFF SWIT CH

Press the EFFE CT button to activate or deactivate the

sound effect. While the effect is activated, on the display
the mark

above the effect is light. .

23. EFFECT SELECT KNOB

The parameter of sound effect can be pre-set. Turn the knob until
the LCD shows the effect name that you want, push the button to

select it, and turn this button again to select from the menu for
setting parameter.

24. EFFECT SCOPE KNOB

After the menu of effect is selected, turn this knob to
choose the parameter, the relative value can be shown in

the LCD.
(Please refer to page 7 with the Parameter Setting
Instruction for details)
When the unit is not under parameter adjustment, the

display does not show the effect name, this knob can be
used to adjust the KE Y scale, and press it to lock the key
(the display will show

)

25. RELAY

Press the “RELAY” button to activate. When one unit is in

play mode, and the other unit is in “pause” mode; pause
the playing unit, the other unit will automatically start to play
(the button will blink).

26. BPM BUTTON

You can get the BPM number automatically or manually.
Pressing the BPM BUTTON for 3 seconds to switch

between  auto  and  manual  control.  The  B EAT  will  be
shown on  the  display!  Under  the  manual  mode,  tapping
this button to get the beat value.

27. KEY ON/OFF SWITCH

Press the button to switch KEY mode on or off.

KEY OFF: The display shows the “KEY” in blinking, and the

key changed according to the pitch change. The key
parameter adjustment is not in effect

KEY ON: The “KEY” lights on the display, turning the

SCOPE knob to adjust the key. Slide the pitch slider will also
change the key.

KEY LOCK: Press the SCOPE knob to lock the key as set,

sliding the pitch slider does not change the key.

Please refer to parameter setting instruction. (Page

)

28. CARD:

Switch the playback source to memory card.