manualshive.com logo in svg

PVA Sigma, Owner'S Manual

Share
Download
PVA Sigma Owner'S Manual Download Page 49

 

Sigma Operation Manual 

 

Revision B 

/

 July 2020 

Page 49 of 68 

 

 

Connect Web Interface to Existing Network 

There is an option to connect an existing 2.4 GHz WiFi network to the web interface.  

Note: This option is not compatible with 5 GHz networks. 

1.

 

Use the steps outlined in Sigma Wireless Connection Setup to connect to Sigma’s 
WiFi network. 

2.

 

Once connected, access the web interface. 

3.

 

Navigate to the G-Code Console.  

 

Figure 53: G-code Console 

 

 

M587 Command 

The M587 command will be used to send your desired network information to the web 
interface’s G-code console. The M587 command must include three components. 

1.

 

S

: Network SSID 

•

 

Must be enclosed in quotation marks 

•

 

Case-sensitive 

2.

 

P

: Network Password 

•

 

Must be enclosed in quotation marks 

•

 

Case-sensitive 

3.

 

I

: IP address to use when connected to this network (optional). 

•

 

If zero is entered or not specified, an IP address will be acquired via DHCP. 

The M587 command must be written in the following format: 

M587

 

S

”WIFI_NETWORK_NAME” 

P

”PASSWORD” 

I

x.xxx.xx.xxx 

 

Summary of Contents for Sigma





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands