PureTools PT-PMS-62S User Manual Download Page 46 | Manualshive

Page: 46 / 64

background image

User Manual

PT-PMS-62S

40

8.2.6

EDID Management

Command

Description

Feedback Example

EDID/[x]/[y].

The input [x] invoke built-in EDID [y].

x=1~3, 5.

y

EDID

1

1080P@60Hz

2

4K@30Hz 4:4:4

3

4K@60Hz 4:4:4

EDID/4/1

EDID Upgrade[x].

Upgrade the EDID data of the input port
[x]. x=1~3, 5.
When the command applied, system
prompts to upload the EDID file (.bin).
Operation will be cancelled in 10
seconds. Please disconnect HDBT
connection before sending command to
ensure the data can be received
successfully.

EDIDM[x]B[y].

Set the EDID data of output [x] to input
[y]. x=1~2, y=1~3, 5.

Example: EDIDM1B1.
Feedback:
Input 1 EDID Upgrade OK By
01 EXT EDID!

EDIDMInit.

Reset factory default EDID to all input
ports.

All input EDID Set Default
1080P!

%9945.

Report the EDID data of all ports.

Inport 1 : Edid_2
Inport 2 : Edid_4
Inport 3 : Edid_1
Inport 4 : Edid_3
Inport 6 : Edid_3
Outport 1 : Edid_3
Outport 2 : Edid_3

«
...
44
45
46
47
48
...
»

Summary of Contents for PT-PMS-62S

































































Reviews:

No comments

Related manuals for PT-PMS-62S

Brand: Cisco Pages: 30

Brand: KELCO Pages: 4

Brand: D-Link Pages: 242

S5170-EI Series

Brand: H3C Pages: 46

Brand: HPM Pages: 4

Temperature SWICHGAGE SPL

Brand: Murphy Pages: 4

Brand: Cabletron Systems Pages: 52

4-Port PoweredUSB 2.0 Hub 011006

Brand: CyberData Pages: 4

Brand: Metrix Pages: 12

UHB-U3P1U2P3P-01

Brand: Gembird Pages: 2

IES8242MPp9H-S-DR

Brand: OTS Pages: 3

Brand: Radio Systems Pages: 19

Brand: 3onedata Pages: 2

Brand: Cypress Pages: 16

Brand: TRENDnet Pages: 2

Brand: Ubiquiti Pages: 23

Brand: Exsys Pages: 2

Brand: Cabletron Systems Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands