PureTools PT-PMS-62S User Manual Download Page 42

Page: 42 / 64

User Manual

PT-PMS-62S

8.2.2

Source Switching

Command

Description

Feedback Example

Demo.

Switch to demo testing mode, switch AV
1>1, 1>2 and so on.

Demo Mode:
AV:01->01
AV:01->02
AV:02->01
AV:02->02
AV:03->01
AV:03->02
AV:04->01
AV:04->02
AV:05->01
AV:05->02
AV:06->01
AV:06->02
Normal Mod

Undo.

Cancel the current operation and return
to the previous switching status.

Undo Ok!

[x]All.

Switch input [x] to HDMI and HDBT
outputs. x=1~6.

Example: 4ALL.
Feedback: 4 To All

All#.

Switch all input signal to the
corresponding output channel. 1->1,
2->2

All Through.

All$.

Turn off all channels.

All Closed.

[x]#.

Switch input [x] to output [x]. x=1~2.

1 Through

[x]$.

Turn off output [x]. x=1~2.

1 Closed.

[x]@.

Turn on output [x]. x=1~2.

01 Open.

All@.

Turn on all outputs.

All Open

[x]V[y].

Switch input [x] to output [y]. x=1~8,
y=1~2.

AV: 1-> 1

%9975.

Report the source switching status.

Out 1 2
In 4 4

Status[x].

Report the output [x] status. x=1~2

AV: 5-> 1

Status.

Report the input channel on output
channel one by one.

AV:01->01
AV:01->02

Summary of Contents for PT-PMS-62S
































































Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands

PureTools PT-PMS-62S, User Manual

Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands