Puretec UF10 Series User Manual Download Page 18

18 

Installation & Operation Manual

Copyright © Puretec Pty Ltd 2020

Warranty

Any claim under this warranty must be made within 1 year of the date of purchase of the 
product. This product is warranted to be free of defect of material and workmanship for 1 year 
from date of purchase. To make a claim under the warranty, take the product and proof of 
purchase to place where you purchased the product, and they will lodge a Warranty Request 
with Puretec. 1 year warranty is 1 year parts and labour. Excludes consumables.

Puretec will pay your reasonable, direct expenses of claiming under this warranty. You may 

submit details and proof of your expense claim to place of purchase for consideration.

The warranty only applies if the product was used and/or installed in accordance with the 
user guide and/or installation instructions. This warranty is given in lieu of all other express 

or implied warranties and manufacturer shall in no circumstance be held liable for damages 
consequential or otherwise or delays caused or faulty manufacturing except as excluded by 
law.

Applicable to all above, is that the warranties need to be approved by Puretec to ensure 
product was not incorrectly used, installed or claimed. False and incorrect claims will be 
pursued at Puretec’s discretion, including chargeable inspection and labour costs incurred.

Warranty/Australia

This warranty is given by Puretec Pty Ltd, ABN 44 164 806 688, 37-43 Brodie Road, Lonsdale 

SA 5160, telephone no. 1300 140 140 and email at [email protected].

This warranty is provided in addition to other rights and remedies you have under law: Our 

goods come with guarantees which cannot be excluded under the Australian Consumer Law.  
You are entitled to replacement or refund for a major failure and to compensation for other 
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or 

replaced if the goods fail to be of acceptable quality and the failure does not amount to a 
major failure. 

Warranty/New Zealand

This warranty is given by Puretec Ltd, Reg. No 4464398, PO Box 875 Cambridge 3450 NZ , 

telephone no. 0800 130 140 and email at [email protected].

This warranty is provided in addition to other rights and remedies you have under law: Our 
goods come with guarantees which cannot be excluded under the Consumer Guarantees Act.  

You are entitled to replacement or refund for a major failure and to compensation for other 
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or 

replaced if the goods fail to be of acceptable quality and the failure does not amount to a 
major failure. 

Summary of Contents for UF10 Series





















Reviews: