background image

www.pulsar.pl 

 

 

 

 

 

AWZ521   

 

 

 
 

 

HEATER outputs 

In  case  of  an  overload  or  a  short  circuit  at  the  HEATER  output,  the  F2  fuse  becomes  permanently 

damaged. Restoration of the output voltage requires replacement of the fuse. 

 
4.2 Maintenance 
Any and all maintenance operations may be performed following the disconnection of the PSU module 

from the power supply network. The PSU module does not require performing any specific maintenance measures, 
however, in case of significant dust ingress, its interior is recommended to be cleaned with compressed air. In case 
of fuse replacement, use a replacement of the same parameters. 
 

The  PSU  module  does  not  require  performing  any  specific  maintenance  measures,  however,  in  case  of 

dust,  clean  the  surface  with  compressed  air.  In  case  of  fuse  replacement,  use  a  replacement  of  the  same 
parameters. 

 

 

WEEE MARK 

 
 

 

According  to  the  EU  WEE  Directive  –  It  is  required  not  to  dispose  of  electric  or 
electronic waste as unsorted municipal waste and to collect such WEEE separately. 
 

 

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

GENERAL WARRANTY CONDITIONS 

 

1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a two-year warranty for the equipment, starting from the initial product date 
of purchase placed on the receipt.  
2. If a purchase proof is missing, a three-year warranty period is counted from the device’s production date.  
3. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the 
manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects, unless such 
defects have been reported within the warranty period (item 1 and 2).  
4. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the 
manufacturer.  
5. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.   
6. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenience, however not 
later that within 14 days from the delivery to the service centre of the manufacturer.  
7. The repair period mentioned in item 6 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the 
equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.  
8. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.  
9. The warranty does not cover the defects of the equipment, resulting from: 
- reasons beyond the manufacturer's control, 
- mechanical damage, 
- improper storage and transport, 
- use that violates the operation manual or equipment’s intended use 
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,  
- improper installation and configuration (in defiance with the manual), 
10. The warranty is void in any of the following circumstances: 
- construction changes  
- repairs carried out by any unauthorized service center 
- damage or removal of warranty labels 
- modifications of the serial number 
11. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the 
wholesale prices suggested by the manufacturer on the day of purchase.  
12. The manufacturer takes no responsibility for the defects that result from:  
- the damaging, malfunctioning or inability to operate the equipment 
- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the 
recommendations and requirements contained in the manual, or the use of the equipment.  

Pulsar K.Bogusz Sp.j.  

Siedlec 150,  32-744 Łapczyca, Poland 

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50 

e-mail: 

[email protected]

[email protected]

 

http:// 

www.pulsar.com.pl

 

 

Summary of Contents for AWZ 521







Reviews: