PTN TPUH-PSU12 User Manual Download Page 8

Page: 8 / 24

Integrated Switching Power Supply

PTN Electronics Limited 4 www.PTN-Electronics.com

3.2 Rear Panel

No.

Name

Description

①

01~12

12 output channals.

DC: 2-Pin phoenix connector, connect with the device
needed to be powered.

SELECT: Press the TACT Switch to select the output
voltage among 5V, 12V, and 24VDC. In addition,
simultaneously long-press this buttons on channel 01 and
channel 02 for 3 seconds or more, the device will be
restored to factory setting.

5/12/24V indicators:



Green when the current selected output voltage is work
normally.



Blinking slowly when the current channel is closed.



Blinking fastly when the current channel is short circuit
or over voltage.

②

RS232

Serial port, 3-Pin phoenix connector, connect with a control
device (such as PC) to control the product via RS232
commands.

③

TCP/IP

Ethernet port, connect with PC to control the product via GUI.

④

AC1& AC2

2 AC input channels. Input voltage is AC100~240V.

Note:

Pictures shown in this manual are for reference only, different model and

specifications are subject to real product.

24V

12V

SELECT

AC100V 240V

RS232

TCP IP

24V

AC100V 240V

AC1

AC2

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

Summary of Contents for TPUH-PSU12
























Search results

Summary of Contents for TPUH-PSU12

Reviews:

Brands by name

Popular brands

PTN TPUH-PSU12, User Manual

Search results

Summary of Contents for TPUH-PSU12

Reviews:

Brands by name

Popular brands