PT AMC123 User Manual Download Page 100 | Manualshive

Page: 100 / 104

background image

Chapter 9: Agency Approvals

100

by meeting the applicable EU standards as outlined in the

Declaration of Conformance

. The

Declaration of Conformance

is available from Performance Technologies, or from your

authorized distributor. Compliance will be demonstrated to the following specifications as listed
in the

Official Journal of the European Communities

.

EN55022 Radiated and Conducted Emissions

EN300 386 Electromagnetic Compatibility (EMC)

EN55024 Immunity

EN61000-4-2

Electro-Static Discharge (ESD)

EN61000-4-3

Radiated Susceptibility

EN61000-4-4

Electrical Fast Transient Burst

EN61000-4-5

Surge Immunity

EN61000-4-6

Frequency Magnetic Fields

EN61000-4-11

Voltage Dips, Variations, and Short Interruptions

Safety

The product described in this manual meets the following safety regulations:

EN/IEC 60950

Safety Requirements for Information Technology Equipment

CB Scheme

CB Scheme Certificate and Report

UL60950

UL Recognized

FCC (USA) Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1. This device may not cause harmful interference, and

«
...
98
99
100
101
102
...
»

Summary of Contents for AMC123









































































































Reviews:

No comments

Related manuals for AMC123

Brand: Panasonic Pages: 5

Brand: JBL Pages: 10

Brand: S.M.S.L Pages: 32

Brand: DUB Edition Pages: 18

Brand: Harman Kardon Pages: 11

Brand: National Instruments Pages: 14

Brand: Radio Shack Pages: 24

Brand: Parasound Pages: 2

BLACK PEARL 30 BP30

Brand: Genz Benz Pages: 8

Brand: DAPAudio Pages: 24

Brand: Crown Pages: 32

Brand: audiophony Pages: 5

Brand: Cyrus Pages: 25

Brand: Technics Pages: 10

Brand: Pro-Ject Audio Systems Pages: 3

Brand: Total Control Pages: 2

Old School 51RT

Brand: Mad Professor Pages: 5

Brand: Kramer Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands