3
4
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure compliance
requirements, please avoid direct contact to the transmitting antenna during
transmitting.
RF Exposure Warning!
This device contains transmitters and receivers which emit Radio Frequency (RF)
energy. The device is designed to comply with the limits for exposure to RF energy set
by the Federal Communications Commission (FCC) of the United States, Industry
Canada (IC) of Canada, and the regulating entities of other countries.
If you are still concerned about exposure to RF energy,
you can further limit your exposure by limiting the
amount of time you use the equipment or by placing
more distance between your body and the device,
since exposure level drops off dramatically
with distance.
2.00-HA February 2021
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: 714.257.0600
TOLL FREE: 800.666.2654
WWW.PRYME.COM
PRYMEBLU BTH-600-HA
Wireless Speaker Microphone
For use with Harris two-way radios with built-in BT.
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products,
Brea CA. All other product or service names are the property of their respective owners.
© 2021 PRYME Radio Products, Brea CA. All Rights Reserved
Model No.: BTH-600-HA
Made in Taiwan
Charging the Speaker Microphone
To charge the Speaker Microphone
1. Ensure the device is turned off using the multifunction button.
2. Plug the charge cable into any powered USB outlet,
such as an AC wall charger, and then into the charge jack
on the Speaker Microphone.
3. Once the charging process has begun, the LED indicator
on the Speaker Microphone will show a constant red light.
4. Typical charge time is approximately five hours. Actual charge
time will vary depending on several factors including the battery’s charge state, condition, and age.
5. When the battery is fully charged the LED indicator on the side of the Speaker Microphone
will turn off.
6. Disconnect the charger from the microphone when charging is completed.
Charging Cautions:
- Do not use a wall charger or charge cable that appears to be damaged. (Example: frayed wires,
melted plastic, etc.) Contact PRYME to get a new manufacturer-approved replacement charger.
- Do not tamper with or modify the Speaker Microphone or charger.
- Always turn the Speaker Microphone off when charging.
The BTH-600-HA Speaker Microphone has a
replaceable Lithium Ion rechargeable battery pack
which must be charged prior to operation, and
must be recharged regularly. A fully charged
battery will provide up to 40 hours of continuous
operation before needing to be recharged.
However, operating time can vary depending on
usage and the condition of the battery pack.
Recharge the battery regularly.
Install optional Button Hook for vehicular mounting (P-CLIP-MP16-BUTTON)
1. Press tab and slide off belt clip
2. Slide on P-CLIP-MP16-BUTTON
Controls and Connection
Emergency Button
Depending on how the radio is
programmed, this can be used to
place the connected two-way
radio into emergency mode.
Front Firing Speaker
Received calls are heard over this speaker.
The volume level can be controlled using
either the Volume Up / Down buttons on
the Speaker Microphone, or by using the
volume controls on the
two-way radio or phone.
Status LEDs
The red and blue LEDs flash
messages that let the user
know the current status of
the Speaker Microphone.
Multifunction Button
Holding down this button for one second
will turn the Speaker Microphone on and off.
This button can also be used to place the Speaker
Microphone into pairing mode so that it can be
connected wirelessly to a compatible two-way radio.
Microphone:
This Microphone picks up the user’s
voice audio when sending a call.
PTT Button
This button is used to
activate the push-to-talk
feature of the 2-way radio
Volume Up and Down Buttons
These buttons can be used to turn
the receive audio volume of the
Speaker Microphone up or down
in five preset steps.
Charge Jack
This mini-USB jack is used to recharge the
removable battery of the Speaker Microphone
by connecting the BTH-600-HA to a USB charger
or any powered USB source
Earphone Jack
This jack is used to connect an (optional)
wired listen-only earphone to the Speaker
Microphone for enhanced privacy.
Battery Cover
The rear cover of the Speaker
Microphone can be removed
by loosening the thumbscrew
on the rear of the Microphone.
This allows the user to gain access
to the removable battery pack.
Removable Battery
The Speaker Microphone is
powered by a removable Lithium
battery pack
Clothing Clip
The alligator-type clip secures the
Speaker Microphone to the user’s
clothing during use. The clip can be
rotated to allow the Microphone to
be better positioned.
