Gebrauchsanleitung
Die erforderliche Breite Ihrer Gabelarbeit einstellen, indem Sie die Stäbe
der Netzgabel in die entsprechenden Löcher der Stege einstecken.
1. Arbeitsschritt
Am Fadenende eine Schlinge bilden wie beim Beginn einer Häkelarbeit.
Unteren Steg der Netzgabel entfernen und rechten Stab durch die Schlinge
stecken. Steg wieder einsetzen.
2. Arbeitsschritt
Garn hinter der Netzgabel halten und um den linken Stab wickeln, indem
Sie die Netzgabel von rechts nach links auf sich zu drehen.
3. Arbeitsschritt
Häkelnadel durch die Schlinge, welche sich jetzt links befindet, stechen.
Faden holen, durch die Schlinge ziehen und eine Luftmasche häkeln.
4. Arbeitsschritt
Häkelnadel mit dem Haken nach unten senkrecht stellen und durch die
Netzgabel führen. Netzgabel von rechts nach links auf sich zu drehen,
wobei das Garn sich um den Stab wickelt. Eine feste Masche in den vorn
liegenden Faden der linken Schlinge häkeln. Diesen Arbeitsgang so oft
wiederholen, bis die gewünschte Anzahl Schlingen erreicht ist.
Tipp
Ist das Fassungsvermögen der Netzgabel erreicht, Schlingen von den
Stäben nehmen und fest aufrollen. Mit einem Maschenraffer sichern und
diesen mit einem Gummiband am unteren Steg befestigen.
Instructions for use
Adjust the ”legs” of the loom by inserting them in the proper holes to give
you the size lace you want.
Step 1
As in crocheting, make a loop at the end of the yarn. Remove the bottom
bar from the loom and insert the right ”leg” into the loop. Replace the bar.
Step 2
Keeping the yarn in the back, wind the yarn around the left ”leg” by
turning the loom from right to left toward you.
Step 3
Insert the crochet hook into the loop which is now at your left, hook and
draw back the yarn through the loop.
Step 4
Raise the hook to an upright position, hook end down, and pass through
the loom. Turn the loom from right to left toward you, wrapping the yarn
around the ”leg” as you turn, completing a tight crocheted stitch in the left
loop. Repeat this step to obtain the desired number of loops.
Tip
Should the required number of loops make the loom too full, remove the
loops from the ”legs” and roll into a tight ball. Secure with a stitch holder
and attach to the bottom bar using a rubber band.
Mode d'emploi
Réglez la largeur nécessaire de votre travail en enfonçant les tiges de la
fourche à dentelle dans les trous correspondants des passerelles.
1
ère
phase de travail
Formez une boucle avec le bout du fil comme on le fait pour un travail
au crochet. Enlevez la passerelle du bas de la fourche à dentelle et piquez
la tige droite à travers la boucle. Remettez la passerelle.
2
ème
phase de travail
Tenez le fil derrière la fourche à dentelle et enroulez-le autour de la tige
gauche, en tournant la fourche à dentelle de droite à gauche vers vous.
3
ème
phase de travail
Piquez le crochet à travers la boucle qui se trouve maintenant sur la
gauche, vous saisissez le fil, vous le passez à travers la boucle et vous
faites une maille en l'air.
4
ème
phase de travail
Mettez le crochet à la verticale avec le crochet vers le bas et faites-le
passer à travers la fourche à dentelle. Tournez la fourche à dentelle de
droite à gauche vers vous, le fil s'enroule autour de la tige. Crochetez une
maille simple dans la boucle gauche. Recommencez cette phase de
travail jusqu'à ce que vous ayez le nombre de boucles souhaité.
Conseil:
Si le nombre de boucles voulu est trop important pour la fourche à
dentelle, enlevez les boucles des tiges et roulez-les. Conservez-les avec
un ramasse-mailles et fixez-les avec un élastique à la passerelle du bas.
Prym . 52220 Stolberg . Germany
www.prym-consumer.com
Aguja de filet universal
.
Forcella universale
Agulha de filet universal
1
4
4
2+3