Proximus Forum Phone 516 User Manual Download

Page: 120 / 156

Main Menu

118

Features and MenuCards

melodies on system telephones if selected, so that you may only hear
parts of some melodies.

4 Message ring tone

: You can set different ringer signals to signal messages

on your system telephone or calls for members of your pick-up group.
These can then be distinguished from one another.
Select

1 Short messages

2 E-Mail

3 Pick-up

4 Voicebox

. For each

type of message you can specify

1 Volume

and

2 Melody

or a short

beeping tone instead of a melody. The short beeping tone is the default
setting for all messages. Use the

keys to select a different

setting.

Note:

When configuring the pick-up groups in your Forum 500 /

Forum 5000’s

Configurator

, your system administrator can also

specify that calls for members of your pick-up group be displayed on
your system telephone as well.

5 En-bloc dialling

: This switches your telephone to automatic dialling (

) or

direct dialling (

Off

Note:

If you use CTI applications, you should

switch off

the “block

dialling” function on your system phone. This applies for all CTI applica-
tions, except for the application

Forum CTI

6 Charge settings

: The charges for automatically dialled external calls can be

displayed on the system telephone as an amount (

Charge

per call),

provided your network operator transmits information about charges.
Alternatively, the

Duration

for internal or external calls can be

displayed on the system telephone. The

Off

setting means that no

charges are displayed.

7 Headset

: If you use a headset with your system telephone, you can switch

this function on and off here. When the headset is switched on you can
make and accept calls by pressing the headset key

. To switch this

function on and off select

1 Headset

and then the option

Off

. If

Option

1 Headset

is switched off, the headset key on your system tele-

phone will not function. You can adjust the volume of the headset and
the microphone to six different levels using the menu items

2 Receiver

vol.

and

3 Sender vol.

. Use the plus/minus key

to adjust the

volume, or enter a number between

…

8 Display

: Select

1 Contrast

2 Language

1 Contrast

lets you adjust the

contrast levels of the display using the

keys (or by entering a

Summary of Contents for Forum Phone 516





























































































































































Search results

Summary of Contents for Forum Phone 516

Reviews:

Related manuals for Forum Phone 516

Brands by name

Popular brands

Proximus Forum Phone 516, User Manual

Search results

Summary of Contents for Forum Phone 516

Reviews:

Related manuals for Forum Phone 516

Brands by name

Popular brands