manualshive.com logo in svg

Proximus forum 523, Mounting And Commissioning Manual

Share
Download
Proximus forum 523 Mounting And Commissioning Manual Download Page 58

Power Failure

56

Installation

Forum 523/524 network connection via ISDN and DSL

Power Failure

In the event of a power failure, all configuration data, voice box messages as 
well as account data are preserved. The internal clock will continue to run for 
about 24 hours. If the power failure lasts for more than 24 hours, the time and 
date are reset to the factory settings when the power is switched on again. 
Depending on the 

System

: 

Common

: 

Synchronize Time

 setting, date and 

time are set to the current values on the first outgoing call as provided by the 
exchange.

Please note:

Do not reset the Forum 523/524 by pulling the plug. Actual 
configuration changes may be lost and reconnecting to a SIP 
provider may need a longer time. Use the code number 
procedure 

* 1 8 5

[System PIN]

#

 instead. 

TAE

DSL

Splitter

NTBA

Switch

DSL & Uk

0

DSL

Modem

Uk

0

S

0

Forum

S

0

WAN

LAN1

PC

Net

PPPoE

LAN2/3

IP-Tel

IP-Tel

Summary of Contents for forum 523





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands