Home
/
Proximus
/
Forum 500 Series
/
Mounting And Commissioning Manual

Proximus Forum 500 Series, Mounting And Commissioning Manual

Share

Page: 119 / 348

Proximus Forum 500 Series Mounting And Commissioning Manual Download Page 119

Forum Gateway 560 Modules

117

Forum 550 Power Supply

Field of application

The Forum 550 Power Supply unit supplies power to the first six slots (1 to 6)
of a Forum Gateway 560. It converts the (220 V/110 V) AC input voltage into
DC v3.3 V and –42 V.

If the remaining slots (7 to 12) are to be used, a second Forum 550 Power
Supply unit will need to be installed.

Forum 550 Power Supply: Front view

MPS+1-AC

«
...
117
118
119
120
121
...
»

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands