manualshive.com logo in svg

Proxim ORiNOCO AP-8000, User Manual, Page: 110 / 178

Share
Download
Proxim ORiNOCO AP-8000 User Manual Download Page 110

Using CLI to Manage the Access Point

AP-8000 User Guide

110

Introduction

The 

Command Line Interface (CLI)

 is a text-based configuration utility that supports a set of keyboard commands and 

parameters to configure and manage a AP-8000 unit. You can enter command statements, composed of CLI commands 
and their associated parameters. These command statements can be entered from the keyboard for real-time control or 
from scripts that automate configuration.

You can use CLI as an alternative to the Web Interface. You can, for example, quickly change multiple settings by running 
commands in a batch. Administrators can use CLI to control radio operations and to monitor network statistics. The 
AP-8000 products support two types of CLI: Boot Loader CLI and normal CLI. The Boot Loader CLI provides a limited 
command set and is used when the current firmware is missing.

NOTE:

When the firmware is missing, the Bootloader CLI can be used to upload the new firmware.

Accessing the Command Line Interface

You can access the CLI over a serial connection (E.g., HyperTerminal) or through Telnet/SSH. During initial configuration, 
you can use CLI over a serial port connection to configure the unit’s IP address. When accessing CLI through Telnet, you 
can communicate with the unit using a switch or hub, over the Internet, or using an Ethernet cable that is connected 
directly to your computer’s Ethernet port.

Using CLI to Manage the Device

The CLI is a primary interface that allows you to configure, manage, and monitor the device. You can directly execute the 
CLI commands to manage the device.

• The CLI commands may be entered in real-time through a keyboard, or submitted with CLI scripts.
• The CLI can be accessed through both the Serial Port interface and over the Ethernet interface using Telnet.

NOTE:

All CLI commands and parameters are case-sensitive.

General Notes on CLI

Prerequisite Skills and Knowledge

To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts, 
Network Access Infrastructures, and Client-server relationships. In addition, you should be familiar with software setup 
procedures for typical network operating systems and servers.

Notation Conventions

• Computer prompts are displayed in 

bold

 with constant width type. For example: 

[System Name]

>

• Information that you input is displayed in 

bold

 with constant width type.

• The names of keyboard keys, software buttons, and field names are displayed in 

bold

 type. For example: 

Click the 

Configure 

button.

• Screen names are displayed in 

bold italics

.

Navigation and Special Keys

The CLI supports the following navigation and special key functions to move the cursor along the prompt line.

Key

Description

DEL, Backspace (BS)

Delete previous character

Ctrl-B

Moves back along the command line

Summary of Contents for ORiNOCO AP-8000



















































































































































































Reviews:

No comments