Protrol IPC4020 User Manual Download

Page: 25 / 63

IPC402x-UM-2209-1-2.x.x (en)

Ensto Protrol AB

Phone: +46 31 45 82 00

Alfagatan 3

internet: www.protrol.se

431 49 Mölndal, SWEDEN

e-mail: [email protected]

7.2.2.3 IEC 60870-5-101/104

– -104 slave

Settings -

104 slave

Parameter

Description

Range

Factory value

Unit

APDU timeout (t1)

Time limit for sent unconfirmed message.
If the time has expired, communication is closed.

1..3600

ACKN timeout (t2)

Deadline for received unconfirmed messages.
Confirmation (ackn) is sent no later than this time.

1..3600

TEST timeout (t3)

Test message timeout. Test message is sent no
later than this time.

1..3600

k unackn I format
ASDU

Maximum number of unconfirmed messages (I
format). If exceeded, communication is closed.

1..255

w ackn I format ASDU

Maximum number of unconfirmed received
messages (I format). Confirmation (ackn) will be
sent no later than this number.

1..255

Command timetag
timeout

Maximum difference between local time in the unit
and time marking on an order. If the telegram
does not arrive in time, the order is not allowed.

1..3600

Time tag type

Specifies the type of time format IPC402x uses.

CP56

Common address
(CA) size

Size of the RTU address, number of octets.

octet

Object address
(OA) size

Size of the object address, number of octets.

octet

Cause of transmission
(COT) size

Size of

”COT”, number of octets.

octet

7.2.3 IEC 60870-5-101 master - OPTIONAL

IPC4020 can be obtained with the option

IEC -101-master for IPC402x

. With this option, IPC4020 can act

local IEC-101 master, which enables the user to connect an additional number of local -101 slaves.

The settings are found on the

Communication/IEC 60870-5-101/104/-101 master

tab.

This is for information only and cannot be changed by the user.

Summary of Contents for IPC4020
































































Search results

Summary of Contents for IPC4020

Reviews:

Related manuals for IPC4020

Brands by name

Popular brands

Protrol IPC4020, User Manual

Search results

Summary of Contents for IPC4020

Reviews:

Related manuals for IPC4020

Brands by name

Popular brands