background image

Operation 

 

 

Page 46 of 69 

 

4.2.1.

 

I

NPUT 

A

SSEMBLY

 

 
The following parameters are used in the input assembly of the module: 
 

Parameter 

Datatype 

Description 

Instance 

STRING 

The  instance  name  of  the  module  that  was  configured  under  the 
general DF1 configuration in the PLX50 Configuration Utility. 

Status.Reserved 

BOOL 

Reserved 

Status.ReactiveTagMode 

BOOL 

Set if the module is operating in DF1 Slave mode. 

Status.ScheduledTagMode 

BOOL 

Set if the module is operating in Scheduled Tag mode. 

Status.ConfigurationValid 

BOOL 

Set if a valid configuration is executing in the module. 

Status.RoutingInhibited 

BOOL 

Set when the module’s routing function has been inhibited. Routing 
can be inhibited by setting a bit in the output assembly of the module. 

Status.ScheduledTagStatus0…19 

BOOL[20] 

Each  bit  represents  the  status  of  the  last  scheduled  transaction  for 
that specific map item. A true value indicates success.   

TransactionRate 

DINT 

The transaction rate is the number of DF1 messages per second that 
the module is currently routing. 

DeviceTemperature 

REAL 

The internal temperature of the module. 

DF1RxPacketCount 

DINT 

The total number of DF1 packets received by the module. 

DF1TxPacketCount 

DINT 

The number of DF1 packets sent by the module. 

DF1ChecksumErrors 

DINT 

The number of corrupted DF1 packets received by the module. 

PCCCRequests 

DINT 

The  total  number  of  DF1  message  routing  requests  received  by  the 
module when operating in Bridge mode. 

PCCCFailures 

DINT 

The  total  number  of  DF1  message  routing  requests  that  resulted  in 
errors when operating in Bridge mode.  

TagReads 

DINT 

The  total  number  of  tag  reads  executed  by  the  module  when 
operating in Tag Map mode. 

TagWrites 

DINT 

The  total  number  of  tag  writes  executed  by  the  module  when 
operating in Tag Map mode. 

TagConnectionFailures 

DINT 

The number of failed class 3 connection attempts when operating in 
Tag Map mode.  

Tag reading and writing requires the module to first establish a class 
3 connection with the Logix Controller.  

TagErrors 

DINT 

The number of failed tag access (read/write) requests when operating 
in tag Map mode. 

These may include privileged violations, non-existing tags, etc. 

 

Table 4.1 - RSLogix 5000 input assembly parameters 

 

Summary of Contents for PLX51-DF1-MSG






































































Reviews: