manualshive.com logo in svg

Promise Technology FAST TRAK S150, User Manual

Share
Download
Promise Technology FAST TRAK S150 User Manual Download Page 58

FastTrak SX4030, SX4060, S150 SX4-M User Manual

50

System locks up during boot up or when Windows starts

There may be a possible IRQ conflict with an ISA card. Identify what IRQs 
are used by ISA cards, enter the Motherboard PCI Setup, and reserve the 
IRQ for use with ISA. PCI slots cannot share IRQs with ISA cards.

Miscellaneous problems such as: 

•

FastTrak BIOS does not appear during boot 

•

FastTrak driver does not load 

•

Slow data transfer rates 

Move the FastTrak card to a different PCI slot. 

Intermittent data problems

Overclocking the PCI bus may cause the system to hang or data corruption. 
If you experience either of these problems and you are overclocking the PCI 
bus, set the PCI bus back to its normal setting to see if this is causing the 
errors.

System CMOS Issues 

Set Motherboard CMOS Boot sequence to boot to the FastTrak card

On some Motherboard BIOS, it is necessary to set the Boot sequence to 
SCSI, A:, C: since the Promise card is identified as a SCSI card.

 Motherboard CMOS displays C: or D: drive failure during startup

See the Drive-Related Errors section.

Using an Onboard IDE Card with FastTrak card

If an onboard IDE controller is installed with hard disks, enable support in the 
Motherboard Standard CMOS Setup for the drives. Note that the onboard 
IDE hard drives will then be the bootable hard disk unless the system BIOS 
has a boot sequence setting with the option to specify booting to a different 
device.

Drive-Related Errors

Critical Array Status Error Reported during Boot

If a critical status error message appears on the FastTrak BIOS startup 
screen for a mirrored array (see below), there is a drive in the array that has 
failed or is not responding. The FastTrak controller will identify the failed 
drive by channel number. The mirrored array has lost its fault tolerance, but 
will still perform normal drive reads and writes.

Summary of Contents for FAST TRAK S150











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands