ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 84

Page: 84 / 140

15.1.2 Calibrating the ORP Sensor

15.1.2.1

Selecting the calibration process for ORP

There are two calibration processes available for calibrating the

controller:

1-point (with buffer solution)

Data input

Continuous display ➨

CAL ORP

Pot. equalisation

Calibration process

A1027

0.0 mV

Offset

Last calibration

CAL setup

13:26:11

11/04/2013

continue with <CAL>

1 point

Fig. 45: [ORP] calibration menu

The calibration menu is displayed.

Use to select the Setup menu or start calibration by

pressing

[CAL Setup]: Press

The menu for selecting the calibration process appears.

Using the arrow keys select the required menu item

[Calibration process] and press

The input window appears.

Use the arrow keys to select the calibration process and

press

Continue with

You can now start your chosen calibration process.

15.1.2.2

1-point calibration of ORP sensor (CAL)

Correct sensor operation
–

Correct measuring and metering is only pos‐

sible if the sensor is working perfectly

–

Refer to the sensor's operating instructions

–

Remove the sensor from the in-line probe

housing and re-fit it for calibration. To do this,

refer to the operating instructions for your in-

line probe housing

Selecting the calibration process

Calibrating the controller diaLog DACb

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 84 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: