ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 59

Page: 59 / 140

11.2 Operating diagram for measured variable: Inductive conductivity

11.2.1 Overview of equipment/Operating elements

User qualification: instructed user, see

Chapter 2.5 ‘User

qualification’ on page 15

A0291

Fig. 25: Overview of equipment/Operating elements

Function

Description

1st respective measured vari‐

able

Affix the measured variable label here

2. LCD display

3. UP key

To increase a displayed numerical value and move up in the operating

4. INFO/RIGHT key

Opens the information menu or moves the cursor one place to the right

5. OK key

To apply, confirm or save a displayed value or status or To confirm an

alarm

6. DOWN key

To decrease a displayed numerical value and move down in the operating

7. MENU key

To access the controller's operating menu

8. STOP/START key

Starts and stops the control and metering function

9. ESC key

Moves one level back in the operating menu, without storing or changing

entries or values
Switches the measured variables in the continuous display.

10. CAL key

To access the calibration selection menu (cell constant and temperature

coefficient) and navigate within the calibration menu.

11. f-REL LED

Shows the activated state of the f-relay

User interface of the controllers

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 59 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: