ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 58

Page: 58 / 140

Fig. 24: Alarm message, controller stops control

11.1.5 Key Lock

The controller has a key lock. If the key lock is activated, the keys

cannot be pressed. The key lock can be activated or deactivated

by simultaneously pressing and . An activated key lock is indi‐

cated by the

symbol.

11.1.6 Measured variables and measuring inputs

Measured variable

Measuring input

Modul type

pH (mV)
Temperature (mV)
ORP (mV)

VA
VV

mV/mA measuring input or mV/mV

measuring input

pH (mA)
ORP (mA)
mA general
Bromine
Chlorine
Chlorine dioxide
Chlorite
Fluoride
Oxygen
Ozone
Peracetic acid
Hydrogen peroxide
Conductivity (mA)
Temperature (mA)

VA
AA

mV/mA measuring input or mA/mA

measuring input

Conductivity (conductive)

Conductive conductivity

User interface of the controllers

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 58 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: