ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 52

Page: 52 / 140

User interface of the controllers

One or two controllers with different user interfaces can be fitted,

depending on the selection using the identity code, on the

DULCOTROL

measuring and control station. These user inter‐

faces are described here and facilitate basic tasks on the control‐

lers. All other tasks, such as configuring the inputs and outputs

etc., are described in the detailed operating instructions for the

ProMinent

components.

You will find the operating instructions for the ProMinent

compo‐

nents on the manufacturer's homepage .

11.1 Operating concept

11.1.1 Display and keys

A1035

Fig. 17: Operating cross (1) / Active keys are displayed in [black] in the display; inactive keys in [grey].

The following path is shown as an example:
Continuous display ➨ ➨ or

[Calibrate] ➨ ➨ or

[Slope] ➨ ➨ .

Continuous display

[Calibrate]

[Slope]

A1036

Fig. 18: A display change is made within a sequence of actions.
I. Continuous display 1

II. Display 2

III. Display 3

IV. Display 4

The function of the keys is described in the table

Chapter 11.1.2

‘Functions of the keys ’ on page 56.

DACb

User interface of the controllers

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 52 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: