background image

NOTICE!
Nature and source of the danger
Damage to the product or its surroundings.
Measure to be taken to avoid this danger.
Note!
– Denotes a possibly damaging situation. If this is

disregarded, the product or an object in its vicinity

could be damaged.

Type of information
Hints on use and additional information.
Source of the information. Additional measures.
Information!

Denotes hints on use and other useful information.

It does not indicate a hazardous or damaging

situation.

1.2 

Users' qualifications

WARNING!
Danger of injury with inadequately qualified personnel!
The operator of the plant / device is responsible for

ensuring that the qualifications are fulfilled.
If inadequately qualified personnel work on the unit or

loiter in the hazard zone of the unit, this could result in

dangers that could cause serious injuries and material

damage.
– All work on the unit should therefore only be

conducted by qualified personnel.

– Unqualified personnel should be kept away from

the hazard zone

Training

Definition

Instructed personnel

An instructed person is deemed to be a person who has been

instructed and, if required, trained in the tasks assigned to him/her and

possible dangers that could result from improper behaviour, as well as

having been instructed in the required protective equipment and

protective measures.

Trained user

A trained user is a person who fulfils the requirements made of an

instructed person and who has also received additional training

specific to the system from ProMinent or another authorised distribu‐

tion partner.

Trained qualified personnel

A qualified employee is deemed to be a person who is able to assess

the tasks assigned to him and recognize possible hazards based on

his/her training, knowledge and experience, as well as knowledge of

pertinent regulations. The assessment of a person's technical training

can also be based on several years of work in the relevant field.

Introduction

 

 

 

5

Summary of Contents for Dulco flex DFBa 010
















































Reviews: