ProLights ArcPod 15VW User Manual Download Page 20 | Manualshive

Page: 20 / 24

background image

BARN DOOR (CODE A15QBD - OPTIONAL)

1

2

Insert the two marked pin on down edge of the barn door into the holes provided on the unit (1) and

positioning the spring pin on the hardware into the hole provided on the top (2).

3

4

Hook the safety cable (3) and adjust the angle of the four leafs (4).

Fig. 11

PROLIGHTS - ArcPod

15VW

18

«
...
18
19
20
21
22
...
»

Summary of Contents for ArcPod 15VW

























Reviews:

No comments

Related manuals for ArcPod 15VW

Brand: ICS ELECTRONICS Pages: 6

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Bacharach Pages: 2

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

Brand: Daga Pages: 24

Brand: DAF Pages: 68

Brand: Major Pages: 52

Brand: Labnet Pages: 12

Accublock D1301

Brand: Labnet Pages: 13

Brand: PASCO Pages: 30

Contrology Cadillac

Brand: Balanced Body Pages: 7

Brand: Yamaha Pages: 29

Brand: ZacUrate Pages: 2

Brand: ZacUrate Pages: 2

Brand: Zafferano Pages: 2

Brand: Cannon Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands