Procom MD300HGA Manual Download Page 1

CAUTION - FOR YOUR SAFETY

Vent-Free Gas Wall Heater 

Blue Flame

PC-ML062-03D-0904

Model #  MD300HGA

MD300TGA

 WARNING:

This appliance is 

equipped for (Natural and Propane) 

gas. Field conversion is not permitted 

other than between natural or 

propane gases.

  

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED 

       EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY 

       DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.

--

    

Do not store or use gasoline or other flammable vapors and liquids in vicinity   

     of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

 

Do not try to light any appliance.

 

Do not touch any electrical switch; do not use any phone in your building.

 

Immediately call your gas supplier from a neighbor’s phone. Follow the  

            gas supplier’s instructions.

 

If you cannot reach your gas supplier, call the fire department.

--   Installation and service must be performed by a qualified installer, service     

     agency or the gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is 

installed. Provisions for adequate combustion and ventilation air must be provided. 

Refer to 

Air For Combustion and Ventilation section

 on page 6 of this manual.

INSTALLER: DO NOT DISCARD THIS MANUAL – LEAVE FOR HOMEOWNER’S 

FUTURE REFERENCE.

This appliance may be installed in an aftermarket, permanently located manufactured 

(mobile) home, where not prohibited by local codes. This appliance is for use with 

the type of gas indicated on the rating plate only. This appliance is not convertible for 

use with other gases.

Questions about installation, operation, or troubleshooting? 

Before returning to your retailer, 

call customer service department toll-free at 

(877)886-5989.

Summary of Contents for MD300HGA



























Reviews: