background image

TRANSPRO WARRANTY

Warranty Coverage

TransPro products offered by Pro World are warranted against defects in material 

and workmanship. Warranty is void if equipment has been damaged by accident, 

unreasonable use, neglect, unauthorized and/or improper service, or other causes 

not arising out of defects in material and workmanship. This warranty does not cover 

damage caused by normal wear and tear, neglect or lack of proper maintenance. 

This warranty is for the original purchaser/owner only, it is not transferable.

Warranty Duration

The heating element shall be warranted for the life of the heat press. There is a one 

(1) year warranty on major components, circuit boards and all other components. 

Warranty Performance

During the warranty period, and in the event that a situation cannot be resolved by 

telephone/email and upon PRE-AUTHORIZATION from Pro World equipment must 

be shipped, freight prepaid to Pro World for service in the original packaging. After 

30 days, all shipping and insurance expenses to and from Pro World of in-warranty 

equipment is solely the responsibility of the customer. Prior to 30 days the shipping 

costs will be refunded if Pro World deems the equipment to be defective as stated. 

Pro World cannot be held responsible for improper handling or any other damage 

incurred in transit. No charge will be made for labor and components for repair of 

in-warranty equipment. OUT-OF WARRANTY machines will be charged at the repair 

rates in effect at the time the machine is received.

Warranty Disclaimers

Pro World shall not be liable for loss of use of TransPro equipment or other inciden-

tal or consequential costs, expenses, or damages incurred by the original purchaser 

or any other user. The above warranty provisions constitute the entire agreement 

between all parties, and supersede any and all prior written and/or oral representa-

tions and understandings. 

This "Limited Warranty" applies to all TransPro equipment. However, the procedure 

for obtaining service may vary outside the continental United States. Contact your 

Pro World representative for warranty information. The purchaser is responsible for 

compliance with all local laws, regulations and measure. Agreement shall be 

governed by and construed in accordance with all applicable laws of said region.

www.proworldinc.com

Summary of Contents for MP352










Reviews: