PLEASE READ THE INSTRUCTIONS BEFORE
ATTEMPTING TO USE THE NANOSCAN SP SERIES SYSTEM
IDENTIFYING YOUR SYSTEM COMPONENTS
INSTALLING YOUR SYSTEM
• Save this manual as it contains important safety information and operating instructions.
• Before using the system, please follow and adhere to all warnings, safety and operating instructions located
on the product and in this user manual.
• Do not expose the product to open flames, extreme hot or cold temperatures, water or moisture.
• Do not allow objects to fall on or liquids to spill on the product.
• Connect the AC power cord only to designated power sources as marked on the product.
• Make sure the electrical cord is located so that it will not be subject to damage.
• To reduce the risk of damage, unplug the product from the power source before connecting the components together.
•
DANGER
- never alter the AC cord or plug. If the plug will not fit into the outlet, have a proper outlet installed
by a qualified electrician.
• Use only the proper type of power supply cord set (provided with the system) for this unit.
• Do not attempt to disassemble the product. Doing so will void the warranty. This product does not contain
consumer serviceable components. Service should be performed by authorized service centers.
NANOSCAN SP SERIES QUICK START INSTRUCTIONS
The standard NanoScan SP Series system consist of:
(1)
NanoScan SP Series Piezo Sample Scanner
(1)
NPC-D-6110 Controller
and power supply
One or more of the sample accessories listed:
QGSP301XR - extra recessed microtitre plate
QGSP302XR - extra recessed universal specimen
QGSP303XR - extra recessed slide holder
(1)
Adapter plate to mount the NanoScan SP on the
microscope XY stage.
No adapter plate is require for Prior
XY stages H117 & HLD117 (Except HLD117NN).
(
12
)
M4x8 Mounting screws
(1) USB Cable QGPA0096-SK-102 + (1) 1.2 metre BNC to BNC cable Q
(1) RS232C QG-0494-SK-200002
(1) 9 pin gender changer for RS232C QG-0494-SK-200001
(1)
USB stick containing manuals and test report.
Gender changer for
RS232C
SP400/600 Piezo Sample Scanner
Sample Holder
s
Adapter Plate
www.prior.com
STEP 1:
Where an adapter plate is
included, attach it to your XY stage
using the screws provided. Do not
screw the adapter plate for the
HLD117NN in place.
Use all available thread holes to
mount the plate. Lightly nip each screw with a hex key (0.3N
m
/
300cN
m
/ 0.2lbft
t
orque). In the event that the screw bottoms
out
before the head seats,
STOP
. Do not force the screw as it
may
be too long; back the screw out before moving the XY stage.
Shown with base
plate attached to back
of NanoScan SP unit.
STEP 2:
Position the NanoScan
SP
stage aligning the
connection points with
those on the XY stage or
adapter plate. Mount the
stage using M4 screws
using all the available
thread holes on the XY
stage. Where the attach-
ment requires screws of
nonstandard length they
should be part of the
adapter kit. Lightly
tighten each screw with a hex hey (0.3N
m
/ 300cN
m
/
0.2lbft Torque). In the event that the screw bottoms out
before the head seats,
STOP
. Do not force the screw as
it
may be too long; back the screw out before moving the XY
stage. It is important to attach the stage using as many
mounts at possible to achieve the specified performance.
Note: The stage is a moving platform, the height will vary when powered compared to unpowered. The stage must be mounted
to a flat surface
before being
powered.
Do not connect the stage to a controller until properly mounted.
