manualshive.com logo in svg

Printekmobile LCM20, Operator'S Manual

Share
Download
Printekmobile LCM20 Operator'S Manual Download Page 5

INTRODUCTION 

 
This document is an Operator’s Manual, written for the person connecting and using the PrintekMobile 
LCM20 and LCM25 thermal printers.  Please read this document carefully before making any connection.  
 
A separate Programmer’s Manual provides details of the control codes, and describes the internal 
operation of this product.   
 
NOTES ON PRINTER FIRMWARE REVISIONS (INCLUDING FLASH) 
 
Printek, Inc. reserves the right to modify and improve the firmware in its printer products at any time.  
While every effort is made to ensure backward compatibility, no guarantee in this respect is given or 
implied.   
 
The LCM20 and LCM25 include a flash programmable microcontroller.  This allows firmware upgrades 
under customer control.  Please contact Printek Technical Support for more information. 
 
COPYRIGHT NOTICE AND DISCLAIMER 
 
Copyright © Printek, Inc. 2010, 2011 
Copyright © Able Systems Limited 2005  
 
Printek

®

 is a registered trademark of Printek, Inc. 

Fujitsu

®

 is a registered trademark of Fujitsu Limited. 

Panasonic

®

 is a registered trademark of Panasonic Corporation. 

 
 

1 

Summary of Contents for LCM20




















Reviews:

No comments

Brands by name

Popular brands

Load more brands